1 Content of this directory
2 =========================
5 Read in the geometry, and get alignment data from CDB, and apply
8 Check if alignment is properly applied in simulations
10 Check if a file contains the right calibration data
12 Run overlap checker on a loaded geometry
14 Script that contains a class to compare the raw data written to the
15 digits it's created from.
19 Compare energy loss deposition from Fluka and GEANT3.21
21 (obsolete) Compare the secondary correction from variations in
23 * `CompareTrackRefsAndHits.C`
24 Compare number of track references and hits from simulation
26 Compile other scripts using AcLIC
28 Convert digits to raw data using AliFMDRawWriter
30 Write out all medium parameters in geometry
32 (obsolete) Extract the dead channel information from OCDB files
34 (obsolete) Convert digits to raw data using AliFMD
36 Show digits using AliFMDDisplay
38 Show ESD info using AliFMDDisplay
40 Show MC Hit info using AliFMDDisplay
42 Show RecPoint info using AliFMDDisplay
44 (obsolete) Use THtml to document the FMD code
46 Script that calls DrawCalib
48 Draw Digits versus SDigits using AliFMDInput
50 GUI to draw calibrations
52 Draw ELoss dist from calibrated raw data using AliFMDInput
54 Draw the ELoss from digits using AliFMDInput
56 Draw the ELoss from digits versus multiplicity from rec points
59 Draw the ELoss dist from ESDs using AliFMDInput - somewhat obsolete
63 Draw the ELoss dist versus beta=p/m from MC hits
65 Draw the MC ELoss versus ADCs
67 Draw the MC ELoss versus "multiplicity"
69 Draw the MC ELoss versus sum-able ADCs
71 Draw summary LEGO (absorbtion, radiation length, ...) plots
73 Draw the sum-able ADCs
75 Draw number of track references in each ring
77 Draw the x-section for ELoss from GEANT3.21 X-section run
79 Make dummy detector classes
81 An MC configuration that does no stepping in anything but FMD
83 Dump 10bit words from a DDL file
85 Estimate the size of the FMD ESD object
87 (obsolete) Do an ESD QA run
89 Fancy display of digits using AliFMDFancy
91 Fancy display of MC hits using AliFMDFancy
92 * `FindCommonModeNoise.C`
93 Script to estimate the common mode noise
95 Script to correct OCDB objects according to file name
97 Map from Hardware address to XYZ coordinates
99 Script I used for rapid prototyping of the FMD3 geometry - in
100 particular the support cone
102 Script that contains a class to get the media where a certain track
103 was created. This is used for background studies.
105 Script to get the various cross sections, energy loss, and ranges
106 of a particular particle type in a particular medium. See also
109 (obsolete) Convert MC hits to digits using AliFMD
111 (obsolete) Convert MC hits to sum-able digits using AliFMD
113 Load the Dummy detector class
115 Make the default alignment
116 * `MakeCalibration.C`
117 Make dummy calibrations
119 Make some fake digits
123 Create LEGO plots from geometry
125 Steer running MakeLego.C and DrawLego.C
127 Script to make a class derived from AliFMDMap.
129 Make default reconstruction parameters
130 * `MakeResidualAlignment.C`
131 Make fake residual alignment data.
133 Compile ELoss spectra in output file
135 Steer generation of X-section data (see GetXsection and DrawXsection)
137 Script to make a file with a list of medium numbers for all active
140 Script I used for rapid prototyping of the FMD3 geometry - in
141 particular the support cone
143 Display the pattern of digits
145 Display the pattern of ESD information
147 Display the pattern of MC hits
149 Display the pattern of Raw digits
151 Display the pattern of RecPoints
153 Display the pattern of MC sum-able digits
161 Script that illustrates the poisson Nch estimation from ESD
163 Check Poisson estimate of Nch versus hits
168 * `PrintCalibration.C`
169 Print OCDB calibration data
170 * `PrintSensorVertices.C`
171 Print senser vertices from geometry
173 Convert raw data to ESD using the AliFMDReconstructor
175 (obsolete) Small script to test consistency of writing and
178 Read raw data using AliRawReader and AliFMDRawReader
180 Plot resolution of sensors
182 (obsolete) Run analysis over ESD
184 (obsolete) Run analysis over MC data
186 Run a test of QA framework
188 A script that will run the most simple chain possible. Uses:
194 * `ShowCoordinates.C`
195 A script to dump the physical coordinates as given by the
198 Draw FMD and ITS geometry
202 Acceptance correction from strip length
204 Test align-able volumes
205 * `TestAltroMapping.C`
206 Check integrety of Hardware2Detector and Detector2Hardware
208 Test Read/Write of AliESDFMD object
212 Test the geometry from ESD and from full geometry
214 Test I/O of floating point FMD map
218 Test hardware address map by converting from detector coordinates
219 to hardware address and then back again.
221 Test of AliFMDIndex and AliFMDObjIndex
223 Test of ForAll access to AliFMDMap
227 Test I/O of ALiFMDMap
229 Test I/O of ALiFMDMap
232 * `TestPreprocessor.C`
233 Test the SHUTTLE pre-processor using fake data
234 * `TestRaw2SDigits.C`
235 Test creation of sum-able digits using AliSimulation
237 Test I/O of raw data using AliFMDRawWriter and AliFMDRawReader
239 Check iterative usage of AliFMDRawReader
241 Create an example shaping curve
242 * `TestSurveyToAlignObjs.C`
243 Convert survey data into alignment objects
244 * `TestZeroSuppress.C`
245 Test the zero-suppression filter of AliFMDRawWriter
247 Script to try to fit the reponse function of the VA1 signals, based
248 on a finite number of ALTRO samples.
250 Small script that shows a signal train from a VA1 pre-amp.
252 Small script that I used to make some intial testing of the wafer
257 Script to get the various cross sections, energy loss, and ranges
258 of a particular particle type in a particular medium.
261 Event display using EVE
263 Event display using AliFMDPattern
265 Event display using AliFMDPattern
267 Event display using AliFMDPattern