/**************************************************************************
- * Copyright(c) 1998-1999, ALICE Experiment at CERN, All rights reserved. *
+ * Copyright(c) 2007-2009, ALICE Experiment at CERN, All rights reserved. *
* *
* Author: The ALICE Off-line Project. *
* Contributors are mentioned in the code where appropriate. *
* about the suitability of this software for any purpose. It is *
* provided "as is" without express or implied warranty. *
**************************************************************************/
-
+//
// This class Defines the Geometry for the ITS services and support cones
-// outside of the ceneteral volume (except for the Ceneteral support
-// cylinders. Other classes define the rest of the ITS. Specificaly the ITS
-// The SSD support cone,SSD Support centeral cylinder, SDD support cone,
-// The SDD cupport centeral cylinder, the SPD Thermal Sheald, The supports
+// outside of the central volume (except for the Central support
+// cylinders). Other classes define the rest of the ITS, specifically the
+// SSD support cone, the SSD Support central cylinder, the SDD support cone,
+// the SDD support central cylinder, the SPD Thermal Shield, The supports
// and cable trays on both the RB26 (muon dump) and RB24 sides, and all of
-// the cabling from the ladders/stave ends out past the TPC.
+// the cabling from the ladders/stave ends out past the TPC.
+//
+// Here is the calling sequence associated with this file
+// SPDSector(TGeoVolume *moth,TGeoManager *mgr)
+// -----CarbonFiberSector(TGeoVolume *moth,Double_t &xAAtubeCenter0,
+// Double_t &yAAtubeCenter0,TGeoManager *mgr)
+// -----2* SPDsectorShape(Int_t n,const Double_t *xc,const Double_t *yc,
+// | const Double_t *r,const Double_t *ths,
+// | const Double_t *the,Int_t npr,Int_t &m,
+// | Double_t **xp,Double_t **yp)
+// -----StavesInSector(TGeoVolume *moth,TGeoManager *mgr)
+// -----3* CreaeStave(Int_t layer,TArrayD &sizes,Bool_t addClips,
+// | TGeoManager *mgr)
+// | -----2* CreateHalfStave(Boot_t isRight,Int_t layer,
+// | Int_t idxCentral,Int_t idxSide,
+// | TArrayD &sizes,Bool_t addClips,
+// | TGeoManager *mgr)
+// | -----CreateGrondingFoil(Bool_t isRight,TArrayD &sizes,
+// | | TGeoManager *mgr)
+// | | -----4* CreateGroundingFoilSingle(Int_t type,
+// | | TArrayD &sizes,
+// | | TGeoManger *mgr)
+// | |----CreateLadder(Int_t layer, TArrayD &sizes,
+// | | TGeoManager *mgr)
+// | |----CreateMCM(Bool_t isRight,TArrayD &sizes,
+// | | TGeoManger *mgr)
+// | |----CreatePixelBus(Bool_t isRight,TArrayD &sizes,
+// | | TGeoManager *mgr)
+// | -----CreateClip(TArrayD &sizes,TGeoManager *mgr)
+// |----GetSectorMountingPoints(Int_t index,Double_t &x0,
+// | Double_t &y0,Double_t &x1,
+// | Double_t y1)
+// -----3* ParallelPosition(Double_t dist1,Double_t dist2,
+// Double_t phi,Double_t &x,Double_t &y)
+//
+// Obsoleate or presently unused routines are: setAddStave(Bool_t *mask),
+// CreatePixelBusAndExtensions(...) which calles CreateExtender(...).
/* $Id$ */
+
+
// General Root includes
#include <Riostream.h>
#include <TMath.h>
#include <TLatex.h>
#include <TCanvas.h>
#include <TPolyLine.h>
+#include <TPolyMarker.h>
+
// Root Geometry includes
-#include <TGeoManager.h>
-#include <TGeoVolume.h>
-#include <TGeoPcon.h>
-#include <TGeoCone.h>
-#include <TGeoTube.h> // contaings TGeoTubeSeg
-#include <TGeoArb8.h>
-#include <TGeoEltu.h>
-#include <TGeoXtru.h>
#include <TGeoCompositeShape.h>
+#include <TGeoEltu.h>
+#include <TGeoGlobalMagField.h>
+#include <TGeoMaterial.h>
#include <TGeoMatrix.h>
-//#include <TGeoRotation.h>
-//#include <TGeoCombiTrans.h>
-//#include <TGeoTranslation.h>
+#include <TGeoMedium.h>
+#include <TGeoTube.h> // contains TGeoTubeSeg
+#include <TGeoVolume.h>
+#include <TGeoXtru.h>
+
+// AliRoot includes
+#include "AliLog.h"
+#include "AliMagF.h"
+#include "AliRun.h"
+
+// Declaration file
#include "AliITSv11GeometrySPD.h"
+// Constant definistions
+const Double_t AliITSv11GeometrySPD::fgkGapLadder =
+ AliITSv11Geometry::fgkmicron*75.; // 75 microns
+const Double_t AliITSv11GeometrySPD::fgkGapHalfStave =
+ AliITSv11Geometry::fgkmicron*120.; // 120 microns
+
ClassImp(AliITSv11GeometrySPD)
+//______________________________________________________________________
+AliITSv11GeometrySPD::AliITSv11GeometrySPD(/*Double_t gap*/):
+AliITSv11Geometry(),// Default constructor of base class
+fAddStave(), // [DEBUG] must be TRUE for all staves which will be
+ // mounted in the sector (used to check overlaps)
+fSPDsectorX0(0), // X of first edge of sector plane for stave
+fSPDsectorY0(0), // Y of first edge of sector plane for stave
+fSPDsectorX1(0), // X of second edge of sector plane for stave
+fSPDsectorY1(0), // Y of second edge of sector plane for stave
+fTubeEndSector() // coordinate of cooling tube ends
+{
+ //
+ // Default constructor.
+ // This does not initialize anything and is provided just for
+ // completeness. It is recommended to use the other one.
+ // The alignment gap is specified as argument (default = 0.0075 cm).
+ // Inputs:
+ // none.
+ // Outputs:
+ // none.
+ // Return:
+ // A default constructed AliITSv11GeometrySPD class.
+ //
+ Int_t i = 0,j=0,k=0;
+
+ for (i = 0; i < 6; i++) fAddStave[i] = kTRUE;
+ for(k=0;k<10;k++)for(i=0;i<6;i++)for(j=0;j<3;j++){
+ this->fTubeEndSector[k][0][i][j] = 0.0;
+ this->fTubeEndSector[k][1][i][j] = 0.0;
+ } // end for i,j
+}
+//______________________________________________________________________
+AliITSv11GeometrySPD::AliITSv11GeometrySPD(Int_t debug/*, Double_t gap*/):
+AliITSv11Geometry(debug),// Default constructor of base class
+fAddStave(), // [DEBUG] must be TRUE for all staves which will be
+ // mounted in the sector (used to check overlaps)
+fSPDsectorX0(0), // X of first edge of sector plane for stave
+fSPDsectorY0(0), // Y of first edge of sector plane for stave
+fSPDsectorX1(0), // X of second edge of sector plane for stave
+fSPDsectorY1(0), // Y of second edge of sector plane for stave
+fTubeEndSector() // coordinate of cooling tube ends
+{
+ //
+ // Constructor with debug setting argument
+ // This is the constructor which is recommended to be used.
+ // It sets a debug level, and initializes the name of the object.
+ // The alignment gap is specified as argument (default = 0.0075 cm).
+ // Inputs:
+ // Int_t debug Debug level, 0= no debug output.
+ // Outputs:
+ // none.
+ // Return:
+ // A default constructed AliITSv11GeometrySPD class.
+ //
+ Int_t i = 0,j=0,k=0;
+
+ for (i = 0; i < 6; i++) fAddStave[i] = kTRUE;
+ for(k=0;k<10;k++)for(i=0;i<6;i++)for(j=0;j<3;j++){
+ this->fTubeEndSector[k][0][i][j] = 0.0;
+ this->fTubeEndSector[k][1][i][j] = 0.0;
+ } // end for i,j
+}
+//______________________________________________________________________
+AliITSv11GeometrySPD::AliITSv11GeometrySPD(const AliITSv11GeometrySPD &s):
+AliITSv11Geometry(s),// Base Class Copy constructor
+fAddStave(), // [DEBUG] must be TRUE for all staves which will be
+ // mounted in the sector (used to check overlaps)
+fSPDsectorX0(s.fSPDsectorX0), // X of first edge of sector plane for stave
+fSPDsectorY0(s.fSPDsectorY0), // Y of first edge of sector plane for stave
+fSPDsectorX1(s.fSPDsectorX1), // X of second edge of sector plane for stave
+fSPDsectorY1(s.fSPDsectorY1) // Y of second edge of sector plane for stave
+{
+ //
+ // Copy Constructor
+ // Inputs:
+ // AliITSv11GeometrySPD &s source class
+ // Outputs:
+ // none.
+ // Return:
+ // A copy of a AliITSv11GeometrySPD class.
+ //
+ Int_t i=0,j=0,k=0;
+
+ for (i = 0; i < 6; i++) this->fAddStave[i] = s.fAddStave[i];
+ for(k=0;k<10;k++)for(i=0;i<6;i++)for(j=0;j<3;j++){
+ this->fTubeEndSector[k][0][i][j] = s.fTubeEndSector[k][0][i][j];
+ this->fTubeEndSector[k][1][i][j] = s.fTubeEndSector[k][1][i][j];
+ } // end for i,j
+}
+//______________________________________________________________________
+AliITSv11GeometrySPD& AliITSv11GeometrySPD::operator=(const
+ AliITSv11GeometrySPD &s)
+{
+ //
+ // = operator
+ // Inputs:
+ // AliITSv11GeometrySPD &s source class
+ // Outputs:
+ // none.
+ // Return:
+ // A copy of a AliITSv11GeometrySPD class.
+ //
+ Int_t i=0,j=0,k=0;
+
+ if(this==&s) return *this;
+ for (i = 0; i < 6; i++) this->fAddStave[i] = s.fAddStave[i];
+ this->fSPDsectorX0=s.fSPDsectorX0;
+ this->fSPDsectorY0=s.fSPDsectorY0;
+ this->fSPDsectorX1=s.fSPDsectorX1;
+ this->fSPDsectorY1=s.fSPDsectorY1;
+ for(k=0;k<10;k++)for(i=0;i<6;i++)for(j=0;j<3;j++){
+ this->fTubeEndSector[k][0][i][j] = s.fTubeEndSector[k][0][i][j];
+ this->fTubeEndSector[k][1][i][j] = s.fTubeEndSector[k][1][i][j];
+ } // end for i,j
+ return *this;
+}
+//______________________________________________________________________
+TGeoMedium* AliITSv11GeometrySPD::GetMedium(const char* mediumName,
+ TGeoManager *mgr) const
+{
+ //
+ // This function is used to recovery any medium
+ // used to build the geometry volumes.
+ // If the required medium does not exists,
+ // a NULL pointer is returned, and an error message is written.
+ //
+ Char_t itsMediumName[30];
+
+ sprintf(itsMediumName, "ITS_%s", mediumName);
+ TGeoMedium* medium = mgr->GetMedium(itsMediumName);
+ if (!medium) AliError(Form("Medium <%s> not found", mediumName));
+
+ return medium;
+}
+//______________________________________________________________________
+Int_t AliITSv11GeometrySPD::CreateSPDCentralMaterials(Int_t &medOffset,
+ Int_t &matOffset) const
+{
+ //
+ // Define the specific materials used for the ITS SPD central detectors.
+ // ---
+ // NOTE: These are the same old names.
+ // By the ALICE naming conventions, they start with "ITS SPD ...."
+ // Data taken from ** AliITSvPPRasymmFMD::CreateMaterials() **.
+ // ---
+ // Arguments [the ones passed by reference contain output values]:
+ // - medOffset --> (by ref) starting number of the list of media
+ // - matOffset --> (by ref) starting number of the list of Materials
+ // ---
+ // Inputs:
+ // Int_t &medOffset Starting number of the list of media
+ // Int_t &matOffset Starting number of the list of materials
+ // Outputs:
+ // Int_t &medOffset Ending number of the list of media
+ // Int_t &matOffset Ending number of the list of materials
+ // Return:
+ // The last material indexused +1. (= next avaiable material index)
+ //
+ const Double_t ktmaxfd = 0.1 * fgkDegree; // Degree
+ const Double_t kstemax = 1.0 * fgkcm; // cm
+ const Double_t kdeemax = 0.1;//Fraction of particle's energy 0<deemax<=1
+ const Double_t kepsil = 1.0E-4; //
+ const Double_t kstmin = 0.0 * fgkcm; // cm "Default value used"
+ const Double_t ktmaxfdAir = 0.1 * fgkDegree; // Degree
+ const Double_t kstemaxAir = 1.0000E+00 * fgkcm; // cm
+ const Double_t kdeemaxAir = 0.1;//Fraction of particle's energy 0<deemax<=1
+ const Double_t kepsilAir = 1.0E-4;//
+ const Double_t kstminAir = 0.0 * fgkcm; // cm "Default value used"
+ const Double_t ktmaxfdSi = 0.1 * fgkDegree; // .10000E+01; // Degree
+ const Double_t kstemaxSi = 0.0075 * fgkcm; // .10000E+01; // cm
+ const Double_t kdeemaxSi = 0.1;//Fraction of particle's energy 0<deemax<=1
+ const Double_t kepsilSi = 1.0E-4;//
+ const Double_t kstminSi = 0.0 * fgkcm; // cm "Default value used"
+ //
+ Int_t matindex = matOffset;
+ Int_t medindex = medOffset;
+ TGeoMaterial *mat;
+ TGeoMixture *mix;
+ TGeoMedium *med;
+ //
+ Int_t ifield = (((AliMagF*)TGeoGlobalMagField::Instance()->GetField())->Integ());
+ Double_t fieldm = (((AliMagF*)TGeoGlobalMagField::Instance()->GetField())->Max());
+ Double_t params[8] = {8 * 0.0};
+
+ params[1] = (Double_t) ifield;
+ params[2] = fieldm;
+ params[3] = ktmaxfdSi;
+ params[4] = kstemaxSi;
+ params[5] = kdeemaxSi;
+ params[6] = kepsilSi;
+ params[7] = kstminSi;
+
+ // Definition of materials and mediums.
+ // Last argument in material definition is its pressure,
+ // which is initialized to ZERO.
+ // For better readability, it is simply set to zero.
+ // Then the writing "0.0 * fgkPascal" is replaced by "0."
+ // (Alberto)
+
+ // silicon definition for ITS (overall)
+ mat = new TGeoMaterial("ITS_SI", 28.086, 14.0, 2.33 * fgkgcm3,
+ TGeoMaterial::kMatStateSolid, 25.0*fgkCelsius, 0.);
+ mat->SetIndex(matindex);
+ med = new TGeoMedium("SI", medindex++, mat, params);
+
+ // silicon for ladder chips
+ mat = new TGeoMaterial("SPD SI CHIP", 28.086, 14.0, 2.33 * fgkgcm3,
+ TGeoMaterial::kMatStateSolid, 25.0*fgkCelsius, 0.);
+ mat->SetIndex(matindex);
+ med = new TGeoMedium("SPD SI CHIP", medindex++, mat, params);
+
+ // silicon for pixel bus
+ mat = new TGeoMaterial("SPD SI BUS", 28.086, 14.0, 2.33 * fgkgcm3,
+ TGeoMaterial::kMatStateSolid, 25.0*fgkCelsius, 0.);
+ mat->SetIndex(matindex);
+ med = new TGeoMedium("SPD SI BUS", medindex++, mat, params);
-#define SQ(A) (A)*(A)
+ // carbon fiber material is defined as a mix of C-O-N-H
+ // defined in terms of fractional weights according to 'C (M55J)'
+ // it is used for the support and clips
+ mix = new TGeoMixture("C (M55J)", 4, 1.9866 * fgkgcm3);
+ mix->SetIndex(matindex);
+ mix->DefineElement(0, 12.01070, 6.0, 0.908508078);// C by fractional weight
+ mix->DefineElement(1, 14.00670, 7.0, 0.010387573);// N by fractional weight
+ mix->DefineElement(2, 15.99940, 8.0, 0.055957585);// O by fractional weight
+ mix->DefineElement(3, 1.00794, 1.0, 0.025146765);// H by fractional weight
+ mix->SetPressure(0.0 * fgkPascal);
+ mix->SetTemperature(25.0 * fgkCelsius);
+ mix->SetState(TGeoMaterial::kMatStateSolid);
+ params[3] = ktmaxfd;
+ params[4] = kstemax;
+ params[5] = kdeemax;
+ params[6] = kepsil;
+ params[7] = kstmin;
+ med = new TGeoMedium("ITSspdCarbonFiber", medindex++, mix, params);
+ // air defined as a mixture of C-N-O-Ar:
+ // it is used to fill all containers
+ mix = new TGeoMixture("Air", 4, 1.20479E-3 * fgkgcm3);
+ mix->SetIndex(matindex);
+ mix->DefineElement(0, 12.0107, 6.0, 0.000124); // C by fractional weight
+ mix->DefineElement(1, 14.0067, 7.0, 0.755267); // N by fractional weight
+ mix->DefineElement(2, 15.9994, 8.0, 0.231781); // O by fractional weight
+ mix->DefineElement(3, 39.9480, 18.0, 0.012827); // Ar by fractional weight
+ mix->SetPressure(101325.0 * fgkPascal); // = 1 atmosphere
+ mix->SetTemperature(25.0 * fgkCelsius);
+ mix->SetState(TGeoMaterial::kMatStateGas);
+ params[3] = ktmaxfdAir;
+ params[4] = kstemaxAir;
+ params[5] = kdeemaxAir;
+ params[6] = kepsilAir;
+ params[7] = kstminAir;
+ med = new TGeoMedium("ITSspdAir", medindex++, mix, params);
+
+ // inox stainless steel, defined as a mixture
+ // used for all metallic parts
+ mix = new TGeoMixture("INOX", 9, 8.03 * fgkgcm3);
+ mix->SetIndex(matindex);
+ mix->DefineElement(0, 12.0107, 6., .0003); // C by fractional weight
+ mix->DefineElement(1, 54.9380, 25., .02); // Fe by fractional weight
+ mix->DefineElement(2, 28.0855, 14., .01); // Na by fractional weight
+ mix->DefineElement(3, 30.9738, 15., .00045); // P by fractional weight
+ mix->DefineElement(4, 32.066 , 16., .0003); // S by fractional weight
+ mix->DefineElement(5, 58.6928, 28., .12); // Ni by fractional weight
+ mix->DefineElement(6, 55.9961, 24., .17); // by fractional weight
+ mix->DefineElement(7, 95.84 , 42., .025); // by fractional weight
+ mix->DefineElement(8, 55.845 , 26., .654); // by fractional weight
+ mix->SetPressure(0.0 * fgkPascal);
+ mix->SetTemperature(25.0 * fgkCelsius);
+ mix->SetState(TGeoMaterial::kMatStateSolid);
+ params[3] = ktmaxfdAir;
+ params[4] = kstemaxAir;
+ params[5] = kdeemaxAir;
+ params[6] = kepsilAir;
+ params[7] = kstminAir;
+ med = new TGeoMedium("ITSspdStainlessSteel", medindex++, mix, params);
+
+ // freon gas which fills the cooling system (C+F)
+ mix = new TGeoMixture("Freon", 2, 1.63 * fgkgcm3);
+ mix->SetIndex(matindex);
+ mix->DefineElement(0, 12.0107 , 6.0, 4); // C by fractional weight
+ mix->DefineElement(1, 18.9984032, 9.0, 10); // F by fractional weight
+ mix->SetPressure(101325.0 * fgkPascal); // = 1 atmosphere
+ mix->SetTemperature(25.0 * fgkCelsius);
+ mix->SetState(TGeoMaterial::kMatStateLiquid);
+ params[3] = ktmaxfdAir;
+ params[4] = kstemaxAir;
+ params[5] = kdeemaxAir;
+ params[6] = kepsilAir;
+ params[7] = kstminAir;
+ med = new TGeoMedium("ITSspdCoolingFluid", medindex++, mix, params);
+
+ // return the next index to be used in case of adding new materials
+ medOffset = medindex;
+ matOffset = matindex;
+ return matOffset;
+}
+//______________________________________________________________________
+void AliITSv11GeometrySPD::InitSPDCentral(Int_t offset, TVirtualMC *vmc) const
+{
+ //
+ // Do all SPD Central detector initializations (e.g.: transport cuts).
+ // ---
+ // Here follow some GEANT3 physics switches, which are interesting
+ // for these settings to be defined:
+ // - "MULTS" (MULtiple Scattering):
+ // the variable IMULS controls this process. See [PHYS320/325/328]
+ // 0 - No multiple scattering.
+ // 1 - (DEFAULT) Multiple scattering according to Moliere theory.
+ // 2 - Same as 1. Kept for backward compatibility.
+ // 3 - Pure Gaussian scattering according to the Rossi formula.
+ // - "DRAY" (Delta RAY production)
+ // The variable IDRAY controls this process. See [PHYS430]
+ // 0 - No delta rays production.
+ // 1 - (DEFAULT) Delta rays production with generation of.
+ // 2 - Delta rays production without generation of.
+ // - "LOSS" (continuous energy loss)
+ // The variable ILOSS controls this process.
+ // 0 - No continuous energy loss, IDRAY is set to 0.
+ // 1 - Continuous energy loss with generation of delta rays above
+ // DCUTE (common/GCUTS/) and restricted Landau fluctuations
+ // below DCUTE.
+ // 2 - (DEFAULT) Continuous energy loss without generation of
+ // delta rays
+ // and full Landau-Vavilov-Gauss fluctuations.
+ // In this case the variable IDRAY is forced to 0 to avoid
+ // double counting of fluctuations.
+ // 3 - Same as 1, kept for backward compatibility.
+ // 4 - Energy loss without fluctuation.
+ // The value obtained from the tables is used directly.
+ // ---
+ // Arguments:
+ // Int_t offset --> the material/medium index offset
+ // TVirtualMC *vmc --> pointer to the virtual Monte Carlo default gMC
+ //
+
+ Int_t i, n = 4;
+
+ for(i=0;i<n;i++) {
+ vmc->Gstpar(i+offset, "CUTGAM", 30.0 * fgkKeV);
+ vmc->Gstpar(i+offset, "CUTELE", 30.0 * fgkKeV);
+ vmc->Gstpar(i+offset, "CUTNEU", 30.0 * fgkKeV);
+ vmc->Gstpar(i+offset, "CUTHAD", 30.0 * fgkKeV);
+ vmc->Gstpar(i+offset, "CUTMUO", 30.0 * fgkKeV);
+ vmc->Gstpar(i+offset, "BCUTE", 30.0 * fgkKeV);
+ vmc->Gstpar(i+offset, "BCUTM", 30.0 * fgkKeV);
+ vmc->Gstpar(i+offset, "DCUTE", 30.0 * fgkKeV);
+ vmc->Gstpar(i+offset, "DCUTM", 30.0 * fgkKeV);
+ //vmc->Gstpar(i+offset, "PPCUTM", );
+ //vmc->Gstpar(i+offset, "PAIR", );
+ //vmc->Gstpar(i+offset, "COMPT", );
+ //vmc->Gstpar(i+offset, "PHOT", );
+ //vmc->Gstpar(i+offset, "PFIS", );
+ vmc->Gstpar(i+offset, "DRAY", 1);
+ //vmc->Gstpar(i+offset, "ANNI", );
+ //vmc->Gstpar(i+offset, "BREM", );
+ //vmc->Gstpar(i+offset, "HADR", );
+ //vmc->Gstpar(i+offset, "MUNU", );
+ //vmc->Gstpar(i+offset, "DCAY", );
+ vmc->Gstpar(i+offset, "LOSS", 1);
+ //vmc->Gstpar(i+offset, "MULS", );
+ //vmc->Gstpar(i+offset, "GHCOR1", );
+ //vmc->Gstpar(i+offset, "BIRK1", );
+ //vmc->Gstpar(i+offset, "BRIK2", );
+ //vmc->Gstpar(i+offset, "BRIK3", );
+ //vmc->Gstpar(i+offset, "LABS", );
+ //vmc->Gstpar(i+offset, "SYNC", );
+ //vmc->Gstpar(i+offset, "STRA", );
+ }
+}
+//______________________________________________________________________
+void AliITSv11GeometrySPD::SPDSector(TGeoVolume *moth, TGeoManager *mgr)
+{
+ //
+ // Creates a single SPD carbon fiber sector and places it
+ // in a container volume passed as first argument ('moth').
+ // Second argument points to the TGeoManager which coordinates
+ // the overall volume creation.
+ // The position of the sector is based on distance of
+ // closest point of SPD stave to beam pipe
+ // (figures all-sections-modules.ps) of 7.22mm at section A-A.
+ //
+
+ // Begin_Html
+ /*
+ <img src="http://alice.pd.infn.it/latestdr/Geometric-Revision/assembly.ps"
+ title="SPD Sector drawing with all cross sections defined">
+ <p>The SPD Sector definition. In
+ <a href="http://alice.pd.infn.it/latestdr/Geometric-Revision/assembly.hpgl">HPGL</a> format.
+ <img src="http://alice.pd.infn.it/latestdr/Geometric-Revision/assembly-10-modules.ps"
+ titile="SPD All Sectors end view with thermal sheald">
+ <p>The SPD all sector end view with thermal sheald.
+ <img src="http://alice.pd.infn.it/latestdr/Geometric-Revision/assembly.ps"
+ title="SPD side view cross section">
+ <p>SPD side view cross section with condes and thermal shealds.
+ <img src="http://alice.pd.infn.it/latestdr/Geometric-Revision/SECTION-A_A.jpg"
+ title="Cross section A-A"><p>Cross section A-A.
+ <img src="http://alice.pd.infn.it/latestdr/Geometric-Revision/SECTION-B_B.jpg"
+ title="Cross updated section A-A"><p>Cross updated section A-A.
+ <img src="http://physics.mps.ohio-state.edu/~nilsen/ITSfigures/Sezione_layerAA.pdf"
+ title="Cross section B-B"><p>Cross section B-B.
+ <img src="http://alice.pd.infn.it/latestdr/Geometric-Revision/SECTION-C_C.jpg"
+ title-"Cross section C-C"><p>Cross section C-C.
+ <img src="http://alice.pd.infn.it/latestdr/Geometric-Revision/SECTION-D_D.jpg"
+ title="Cross section D-D"><p>Cross section D-D.
+ <img src="http://alice.pd.infn.it/latestdr/Geometric-Revision/SECTION-E_E.jpg"
+ title="Cross section E-E"><p>Cross section E-E.
+ <img src="http://alice.pd.infn.it/latestdr/Geometric-Revision/SECTION-F_F.jpg"
+ title="Cross section F-F"><p>Cross section F-F.
+ <img src="http://alice.pd.infn.it/latestdr/Geometric-Revision/SECTION-G_G.jpg"
+ title="Cross section G-G"><p>Cross section G-G.
+ */
+ // End_Html
+
+ // Inputs:
+ // TGeoVolume *moth Pointer to mother volume where this object
+ // is to be placed in
+ // TGeoManager *mgr Pointer to the TGeoManager used, defaule is
+ // gGeoManager.
+ // Outputs:
+ // none.
+ // Return:
+ // none.
+ // Updated values for kSPDclossesStaveAA, kBeamPipeRadius, and
+ // staveThicknessAA are taken from
+ // http://physics.mps.ohio-state.edu/~nilsen/ITSfigures/Sezione_layerAA.pdf
+ //
+ const Double_t kSPDclossesStaveAA = 7.25* fgkmm;
+ const Double_t kSectorStartingAngle = -72.0 * fgkDegree;
+ const Int_t kNSectorsTotal = 10;
+ const Double_t kSectorRelativeAngle = 36.0 * fgkDegree; // = 360.0 / 10
+ const Double_t kBeamPipeRadius = 0.5 * 59.6 * fgkmm; // diam. = 59.6 mm
+ //const Double_t staveThicknessAA = 0.9 *fgkmm; // nominal thickness
+ const Double_t staveThicknessAA = 1.02 * fgkmm; // get from stave geometry.
+
+ Int_t i, j, k;
+ Double_t angle, radiusSector, xAAtubeCenter0, yAAtubeCenter0;
+ TGeoCombiTrans *secRot = new TGeoCombiTrans(), *comrot;
+ TGeoVolume *vCarbonFiberSector;
+ TGeoMedium *medSPDcf;
+
+ // Define an assembly and fill it with the support of
+ // a single carbon fiber sector and staves in it
+ medSPDcf = GetMedium("SPD C (M55J)$", mgr);
+ vCarbonFiberSector = new TGeoVolumeAssembly("ITSSPDCarbonFiberSectorV");
+ vCarbonFiberSector->SetMedium(medSPDcf);
+ CarbonFiberSector(vCarbonFiberSector, xAAtubeCenter0, yAAtubeCenter0, mgr);
+
+ // Compute the radial shift out of the sectors
+ radiusSector = kBeamPipeRadius + kSPDclossesStaveAA + staveThicknessAA;
+ radiusSector = GetSPDSectorTranslation(fSPDsectorX0.At(1), fSPDsectorY0.At(1),
+ fSPDsectorX1.At(1), fSPDsectorY1.At(1), radiusSector);
+ //radiusSector *= radiusSector; // squaring;
+ //radiusSector -= xAAtubeCenter0 * xAAtubeCenter0;
+ //radiusSector = -yAAtubeCenter0 + TMath::Sqrt(radiusSector);
+
+ AliDebug(1, Form("SPDSector : radiusSector=%f\n",radiusSector));
+ i = 1;
+ AliDebug(1, Form("i= %d x0=%f y0=%f x1=%f y1=%f\n", i,
+ fSPDsectorX0.At(i), fSPDsectorY0.At(i),
+ fSPDsectorX1.At(i),fSPDsectorY1.At(i)));
+
+ // add 10 single sectors, by replicating the virtual sector defined above
+ // and placing at different angles
+ Double_t shiftX, shiftY, tub[2][6][3];
+ for(i=0;i<2;i++)for(j=0;j<6;j++)for(k=0;k<3;k++) tub[i][j][k] = fTubeEndSector[0][i][j][k];
+ angle = kSectorStartingAngle;
+ secRot->RotateZ(angle);
+ TGeoVolumeAssembly *vcenteral = new TGeoVolumeAssembly("ITSSPD");
+ moth->AddNode(vcenteral, 1, 0);
+ for(i = 0; i < kNSectorsTotal; i++) {
+ shiftX = -radiusSector * TMath::Sin(angle/fgkRadian);
+ shiftY = radiusSector * TMath::Cos(angle/fgkRadian);
+ //cout << "ANGLE = " << angle << endl;
+ shiftX += 0.1094 * TMath::Cos((angle + 196.)/fgkRadian);
+ shiftY += 0.1094 * TMath::Sin((angle + 196.)/fgkRadian);
+ //shiftX -= 0.105;
+ //shiftY -= 0.031;
+ //shiftX -= 0.11 * TMath::Cos(angle/fgkRadian); // add by Alberto
+ //shiftY -= 0.11 * TMath::Sin(angle/fgkRadian); // don't ask me where that 0.11 comes from!
+ secRot->SetDx(shiftX);
+ secRot->SetDy(shiftY);
+ comrot = new TGeoCombiTrans(*secRot);
+ vcenteral->AddNode(vCarbonFiberSector,i+1,comrot);
+ for(j=0;j<2;j++)for(k=0;k<6;k++) // Transform Tube ends for each sector
+ comrot->LocalToMaster(tub[j][k],fTubeEndSector[i][j][k]);
+ if(GetDebug(5)) {
+ AliInfo(Form("i=%d angle=%g angle[rad]=%g radiusSector=%g "
+ "x=%g y=%g \n",i, angle, angle/fgkRadian,
+ radiusSector, shiftX, shiftY));
+ } // end if GetDebug(5)
+ angle += kSectorRelativeAngle;
+ secRot->RotateZ(kSectorRelativeAngle);
+ } // end for i
+ if(GetDebug(3)) moth->PrintNodes();
+ delete secRot;
+
+ CreateCones(moth);
+}
//______________________________________________________________________
-void AliITSv11GeometrySPD::CarbonFiberSector(TGeoVolume *moth){
+void AliITSv11GeometrySPD::CarbonFiberSector(TGeoVolume *moth,
+ Double_t &xAAtubeCenter0, Double_t &yAAtubeCenter0, TGeoManager *mgr)
+{
+ //
// Define the detail SPD Carbon fiber support Sector geometry.
- // Based on the drawings ALICE-Pixel "Construzione Profilo Modulo"
- // March 25 2004 and ALICE-SUPPORTO "construzione Profilo Modulo"
- // Define Outside radii as negitive, Outside in the sence that the
- // center of the arc is outside of the object.
- // February 16 2004.
+ // Based on the drawings:
+ /*
+ http:///QA-construzione-profilo-modulo.ps
+ */
+ // - ALICE-Pixel "Costruzione Profilo Modulo" (march 25 2004)
+ // - ALICE-SUPPORTO "Costruzione Profilo Modulo"
+ // ---
+ // Define outside radii as negative, where "outside" means that the
+ // center of the arc is outside of the object (feb 16 2004).
+ // ---
+ // Arguments [the one passed by ref contain output values]:
// Inputs:
- // none.
+ // TGeoVolume *moth the voulme which will contain this object
+ // TGeoManager *mgr TGeo builder defauls is gGeoManager
// Outputs:
- // none.
+ // Double_t &xAAtubeCenter0 (by ref) x location of the outer surface
+ // of the cooling tube center for tube 0.
+ // Double_t &yAAtubeCenter0 (by ref) y location of the outer surface
+ // of the cooling tube center for tube 0.
// Return:
- // none.
- TGeoManager *mgr = gGeoManager;
- TGeoMedium *medSPDcf = 0; // SPD support cone Carbon Fiber materal number.
- //TGeoMedium *medSPDfs = 0; // SPD support cone inserto stesalite 4411w.
- //TGeoMedium *medSPDfo = 0; // SPD support cone foam, Rohacell 50A.
- TGeoMedium *medSPDss = 0; // SPD support cone screw material,Stainless
- TGeoMedium *medSPDair = 0; // SPD support cone Air
- //TGeoMedium *medSPDal = 0; // SPD support cone SDD mounting bracket Al
- TGeoMedium *medSPDcoolfl = 0; // SPD cooling fluid, Freeon
- medSPDcf = mgr->GetMedium("ITSspdCarbonFiber");
- //medSPDfs = mgr->GetMedium("ITSspdStaselite4411w");
- //medSPDfo = mgr->GetMedium("ITSspdRohacell50A");
- medSPDss = mgr->GetMedium("ITSspdStainlessSteal");
- medSPDair= mgr->GetMedium("ITSspdAir");
- medSPDcoolfl= mgr->GetMedium("ITSspdCoolingFluid");
- //
- const Double_t ksecDz = 0.5*500.0*fgkmm;
- const Double_t ksecLen = 30.0*fgkmm;
- const Double_t ksecCthick = 0.20*fgkmm;
- const Double_t ksecDipLength = 3.2*fgkmm;
- const Double_t ksecDipRadii = 0.4*fgkmm;
- //const Double_t ksecCoolingTubeExtraDepth = 0.86*fgkmm;
- //
- const Double_t ksecX0 = -10.725*fgkmm;
- const Double_t ksecY0 = -14.853*fgkmm;
- const Double_t ksecR0 = -0.8*fgkmm; // Outside
- const Double_t ksecX1 = -13.187*fgkmm;
- const Double_t ksecY1 = -19.964*fgkmm;
- const Double_t ksecR1 = +0.6*fgkmm; // Inside
- const Double_t ksecDip0 = 5.9*fgkmm;
- //
- const Double_t ksecX2 = -3.883*fgkmm;
- const Double_t ksecY2 = -17.805*fgkmm;
- const Double_t ksecR2 = +0.80*fgkmm; // Inside Guess.
- const Double_t ksecX3 = -3.123*fgkmm;
- const Double_t ksecY3 = -14.618*fgkmm;
- const Double_t ksecR3 = -0.6*fgkmm; // Outside
- const Double_t ksecDip1 = 8.035*fgkmm;
- //
- const Double_t ksecX4 = +11.280*fgkmm;
- const Double_t ksecY4 = -14.473*fgkmm;
- const Double_t ksecR4 = +0.8*fgkmm; // Inside
- const Double_t ksecX5 = +19.544*fgkmm;
- const Double_t ksecY5 = +10.961*fgkmm;
- const Double_t ksecR5 = +0.8*fgkmm; // Inside
- const Double_t ksecDip2 = 4.553*fgkmm;
- //
- const Double_t ksecX6 = +10.830*fgkmm;
- const Double_t ksecY6 = +16.858*fgkmm;
- const Double_t ksecR6 = +0.6*fgkmm; // Inside
- const Double_t ksecX7 = +11.581*fgkmm;
- const Double_t ksecY7 = +13.317*fgkmm;
- const Double_t ksecR7 = -0.6*fgkmm; // Outside
- const Double_t ksecDip3 = 6.978*fgkmm;
- //
- const Double_t ksecX8 = -0.733*fgkmm;
- const Double_t ksecY8 = +17.486*fgkmm;
- const Double_t ksecR8 = +0.6*fgkmm; // Inside
- const Double_t ksecX9 = +0.562*fgkmm;
- const Double_t ksecY9 = +14.486*fgkmm;
- const Double_t ksecR9 = -0.6*fgkmm; // Outside
- const Double_t ksecDip4 = 6.978*fgkmm;
- //
- const Double_t ksecX10 = -12.252*fgkmm;
- const Double_t ksecY10 = +16.298*fgkmm;
- const Double_t ksecR10 = +0.6*fgkmm; // Inside
- const Double_t ksecX11 = -10.445*fgkmm;
- const Double_t ksecY11 = +13.162*fgkmm;
- const Double_t ksecR11 = -0.6*fgkmm; // Outside
- const Double_t ksecDip5 = 6.978*fgkmm;
- //
- const Double_t ksecX12 = -22.276*fgkmm;
- const Double_t ksecY12 = +12.948*fgkmm;
- const Double_t ksecR12 = +0.85*fgkmm; // Inside
- //const Double_t ksecX13 = *fgkmm;
- //const Double_t ksecY13 = *fgkmm;
- const Double_t ksecR13 = -0.8*fgkmm; // Outside
- const Double_t ksecAngleSide13 = 36.0*fgkDegree;
- //
- const Int_t ksecNRadii = 14;
+ // none.
+ // ---
+ // Int the two variables passed by reference values will be stored
+ // which will then be used to correctly locate this sector.
+ // The information used for this is the distance between the
+ // center of the #0 detector and the beam pipe.
+ // Measurements are taken at cross section A-A.
+ //
+
+ //TGeoMedium *medSPDfs = 0;//SPD support cone inserto stesalite 4411w
+ //TGeoMedium *medSPDfo = 0;//SPD support cone foam, Rohacell 50A.
+ //TGeoMedium *medSPDal = 0;//SPD support cone SDD mounting bracket Al
+ TGeoMedium *medSPDcf = GetMedium("SPD C (M55J)$", mgr);
+ TGeoMedium *medSPDss = GetMedium("INOX$", mgr);
+ TGeoMedium *medSPDair = GetMedium("AIR$", mgr);
+ TGeoMedium *medSPDcoolfl = GetMedium("Freon$", mgr); //ITSspdCoolingFluid
+ //
+ const Double_t ksecDz = 0.5 * 500.0 * fgkmm;
+ //const Double_t ksecLen = 30.0 * fgkmm;
+ const Double_t ksecCthick = 0.2 * fgkmm;
+ const Double_t ksecDipLength = 3.2 * fgkmm;
+ const Double_t ksecDipRadii = 0.4 * fgkmm;
+ //const Double_t ksecCoolingTubeExtraDepth = 0.86 * fgkmm;
+ //
+ // The following positions ('ksecX#' and 'ksecY#') and radii ('ksecR#')
+ // are the centers and radii of curvature of all the rounded corners
+ // between the straight borders of the SPD sector shape.
+ // To draw this SPD sector, the following steps are followed:
+ // 1) the (ksecX, ksecY) points are plotted
+ // and circles of the specified radii are drawn around them.
+ // 2) each pair of consecutive circles is connected by a line
+ // tangent to them, in accordance with the radii being "internal"
+ // or "external" with respect to the closed shape which describes
+ // the sector itself.
+ // The resulting connected shape is the section
+ // of the SPD sector surface in the transverse plane (XY).
+ //
+ const Double_t ksecX0 = -10.725 * fgkmm;
+ const Double_t ksecY0 = -14.853 * fgkmm;
+ const Double_t ksecR0 = -0.8 * fgkmm; // external
+ const Double_t ksecX1 = -13.187 * fgkmm;
+ const Double_t ksecY1 = -19.964 * fgkmm;
+ const Double_t ksecR1 = +0.6 * fgkmm; // internal // (modif. by Alberto)
+ //const Double_t ksecR1 = +0.8 * fgkmm; // internal // (modif. by Alberto)
+
+ // const Double_t ksecDip0 = 5.9 * fgkmm;
+ //
+ //const Double_t ksecX2 = -3.883 * fgkmm;
+ const Double_t ksecX2 = -3.833 * fgkmm; // (corr. by Alberto)
+ const Double_t ksecY2 = -17.805 * fgkmm;
+ const Double_t ksecR2 = +0.6 * fgkmm; // internal (guess)
+ const Double_t ksecX3 = -3.123 * fgkmm;
+ const Double_t ksecY3 = -14.618 * fgkmm;
+ const Double_t ksecR3 = -0.6 * fgkmm; // external
+ //const Double_t ksecDip1 = 8.035 * fgkmm;
+ //
+ const Double_t ksecX4 = +11.280 * fgkmm;
+ const Double_t ksecY4 = -14.473 * fgkmm;
+ const Double_t ksecR4 = +0.8 * fgkmm; // internal
+ const Double_t ksecX5 = +19.544 * fgkmm;
+ const Double_t ksecY5 = +10.961 * fgkmm;
+ const Double_t ksecR5 = +0.8 * fgkmm; // internal
+ //const Double_t ksecDip2 = 4.553 * fgkmm;
+ //
+ const Double_t ksecX6 = +10.830 * fgkmm;
+ const Double_t ksecY6 = +16.858 * fgkmm;
+ const Double_t ksecR6 = +0.6 * fgkmm; // internal
+ const Double_t ksecX7 = +11.581 * fgkmm;
+ const Double_t ksecY7 = +13.317 * fgkmm;
+ const Double_t ksecR7 = -0.6 * fgkmm; // external
+ //const Double_t ksecDip3 = 6.978 * fgkmm;
+ //
+ const Double_t ksecX8 = -0.733 * fgkmm;
+ const Double_t ksecY8 = +17.486 * fgkmm;
+ const Double_t ksecR8 = +0.6 * fgkmm; // internal
+ const Double_t ksecX9 = +0.562 * fgkmm;
+ //const Double_t ksecY9 = +14.486 * fgkmm; // correction by
+ const Double_t ksecY9 = +14.107 * fgkmm; // Alberto
+ const Double_t ksecR9 = -0.6 * fgkmm; // external
+ //const Double_t ksecDip4 = 6.978 * fgkmm;
+ //
+ const Double_t ksecX10 = -12.252 * fgkmm;
+ const Double_t ksecY10 = +16.298 * fgkmm;
+ const Double_t ksecR10 = +0.6 * fgkmm; // internal
+ const Double_t ksecX11 = -10.445 * fgkmm;
+ const Double_t ksecY11 = +13.162 * fgkmm;
+ const Double_t ksecR11 = -0.6 * fgkmm; // external
+ //const Double_t ksecDip5 = 6.978 * fgkmm;
+ //
+ const Double_t ksecX12 = -22.276 * fgkmm;
+ const Double_t ksecY12 = +12.948 * fgkmm;
+ const Double_t ksecR12 = +0.85 * fgkmm; // internal
+ const Double_t ksecR13 = -0.8 * fgkmm; // external
+ const Double_t ksecAngleSide13 = 36.0 * fgkDegree;
+ //
+ const Int_t ksecNRadii = 20;
const Int_t ksecNPointsPerRadii = 4;
const Int_t ksecNCoolingTubeDips = 6;
- // Since the Rounded parts are aproximated by a regular polygon and
- // a cooling tube of the propper diameter must fit, a scaling factor
+ //
+ // Since the rounded parts are approximated by a regular polygon
+ // and a cooling tube of the propper diameter must fit, a scaling factor
// increases the size of the polygon for the tube to fit.
//const Double_t ksecRCoolScale = 1./TMath::Cos(TMath::Pi()/
- // (Double_t)ksecNPointsPerRadii);
- const Double_t ksecZEndLen = 30.00*fgkmm;
- //const Double_t ksecZFlangLen= 45.00*fgkmm;
- const Double_t ksecTl = 0.860*fgkmm;
- const Double_t ksecCthick2 = 0.600*fgkmm;
- const Double_t ksecCthick3 = 1.800*fgkmm;
- const Double_t ksecSidelen = 22.00*fgkmm;
- const Double_t ksecSideD5 = 3.679*fgkmm;
- const Double_t ksecSideD12 = 7.066*fgkmm;
- const Double_t ksecRCoolOut = 2.400*fgkmm;
- const Double_t ksecRCoolIn = 2.000*fgkmm;
- const Double_t ksecDl1 = 5.900*fgkmm;
- const Double_t ksecDl2 = 8.035*fgkmm;
- const Double_t ksecDl3 = 4.553*fgkmm;
- const Double_t ksecDl4 = 6.978*fgkmm;
- const Double_t ksecDl5 = 6.978*fgkmm;
- const Double_t ksecDl6 = 6.978*fgkmm;
- const Double_t ksecCoolTubeThick = 10.0*fgkmicron;
- //
- const Int_t ksecNPoints = (ksecNPointsPerRadii+1)*(ksecNRadii+
- ksecNCoolingTubeDips) + 8;
- Double_t secX[ksecNRadii] = {ksecX0,ksecX1,ksecX2,ksecX3,ksecX4,ksecX5,
- ksecX6,ksecX7,ksecX8,ksecX9,ksecX10,ksecX11,
- ksecX12,-1000.0};
- Double_t secY[ksecNRadii] = {ksecY0,ksecY1,ksecY2,ksecY3,ksecY4,ksecY5,
- ksecY6,ksecY7,ksecY8,ksecY9,ksecY10,ksecY11,
- ksecY12,-1000.0};
- Double_t secR[ksecNRadii] = {ksecR0,ksecR1,ksecR2,ksecR3,ksecR4,ksecR5,
- ksecR6,ksecR7,ksecR8,ksecR9,ksecR10,ksecR11,
- ksecR12,ksecR13};
- Double_t secDip[ksecNRadii]={0.0,ksecDip0,0.0,ksecDip1,0.0,ksecDip2,0.0,
- ksecDip3,0.0,ksecDip4,0.0,ksecDip5,0.0,0.0};
- Double_t secX2[ksecNRadii+ksecNCoolingTubeDips] = {
- ksecX0,ksecX1,-1000.,ksecX2,ksecX3,-1000.,ksecX4,ksecX5,
- -1000.,ksecX6,ksecX7,-1000.,ksecX8,ksecX9,-1000.,
- ksecX10,ksecX11,-1000.,ksecX12,-1000.0};
- Double_t secY2[ksecNRadii+ksecNCoolingTubeDips] = {
- ksecY0,ksecY1,-1000.,ksecY2,ksecY3,-1000.,ksecY4,ksecY5,
- -1000.,ksecY6,ksecY7,-1000.,ksecY8,ksecY9,-1000.,
- ksecY10,ksecY11,-1000.,ksecY12,-1000.0};
- Double_t secR2[ksecNRadii+ksecNCoolingTubeDips] = {
- ksecR0,ksecR1,ksecRCoolOut,ksecR2,ksecR3,ksecRCoolOut,ksecR4,ksecR5,
- ksecRCoolOut,ksecR6,ksecR7,ksecRCoolOut,ksecR8,ksecR9,ksecRCoolOut,
- ksecR10,ksecR11,ksecRCoolOut,ksecR12,ksecR13};
- Double_t secDip2[ksecNRadii]={0.0,ksecDl1,0.0,ksecDl2,0.0,ksecDl3,0.0,
- ksecDl4,0.0,ksecDl5,0.0,ksecDl6,0.0,0.0};
- const Int_t ksecDipIndex[ksecNCoolingTubeDips] = {2,5,8,11,14,17};
+ // (Double_t)ksecNPointsPerRadii);
+ const Double_t ksecZEndLen = 30.000 * fgkmm;
+ //const Double_t ksecZFlangLen = 45.000 * fgkmm;
+ const Double_t ksecTl = 0.860 * fgkmm;
+ const Double_t ksecCthick2 = 0.600 * fgkmm;
+ //const Double_t ksecCthick3 = 1.80 * fgkmm;
+ //const Double_t ksecSidelen = 22.0 * fgkmm;
+ //const Double_t ksecSideD5 = 3.679 * fgkmm;
+ //const Double_t ksecSideD12 = 7.066 * fgkmm;
+ const Double_t ksecRCoolOut = 2.400 * fgkmm;
+ const Double_t ksecRCoolIn = 2.000 * fgkmm;
+ const Double_t ksecDl1 = 5.900 * fgkmm;
+ const Double_t ksecDl2 = 8.035 * fgkmm;
+ const Double_t ksecDl3 = 4.553 * fgkmm;
+ const Double_t ksecDl4 = 6.978 * fgkmm;
+ const Double_t ksecDl5 = 6.978 * fgkmm;
+ const Double_t ksecDl6 = 6.978 * fgkmm;
+ const Double_t ksecCoolTubeThick = 0.04 * fgkmm;
+ const Double_t ksecCoolTubeROuter = 2.6 * fgkmm;
+ const Double_t ksecCoolTubeFlatX = 3.696 * fgkmm;
+ const Double_t ksecCoolTubeFlatY = 0.68 * fgkmm;
+ //const Double_t ksecBeamX0 = 0.0 * fgkmm; // guess
+ //const Double_t ksecBeamY0 = (15.223 + 40.) * fgkmm; // guess
+ //
+ // redefine some of the points already defined above
+ // in the format of arrays (???)
+ const Int_t ksecNPoints = (ksecNPointsPerRadii + 1) * ksecNRadii + 8;
+ Double_t secX[ksecNRadii] = {
+ ksecX0, ksecX1, -1000.0,
+ ksecX2, ksecX3, -1000.0,
+ ksecX4, ksecX5, -1000.0,
+ ksecX6, ksecX7, -1000.0,
+ ksecX8, ksecX9, -1000.0,
+ ksecX10, ksecX11, -1000.0,
+ ksecX12, -1000.0
+ };
+ Double_t secY[ksecNRadii] = {
+ ksecY0, ksecY1, -1000.0,
+ ksecY2, ksecY3, -1000.0,
+ ksecY4, ksecY5, -1000.0,
+ ksecY6, ksecY7, -1000.0,
+ ksecY8, ksecY9, -1000.0,
+ ksecY10, ksecY11, -1000.0,
+ ksecY12, -1000.0
+ };
+ Double_t secR[ksecNRadii] = {
+ ksecR0, ksecR1, -.5 * ksecDipLength - ksecDipRadii,
+ ksecR2, ksecR3, -.5 * ksecDipLength - ksecDipRadii,
+ ksecR4, ksecR5, -.5 * ksecDipLength - ksecDipRadii,
+ ksecR6, ksecR7, -.5 * ksecDipLength - ksecDipRadii,
+ ksecR8, ksecR9, -.5 * ksecDipLength - ksecDipRadii,
+ ksecR10, ksecR11, -.5 * ksecDipLength - ksecDipRadii,
+ ksecR12, ksecR13
+ };
+ /*
+ Double_t secDip[ksecNRadii] = {
+ 0., 0., ksecDip0, 0., 0., ksecDip1,
+ 0., 0., ksecDip2, 0., 0., ksecDip3,
+ 0., 0., ksecDip4, 0., 0., ksecDip5,
+ 0., 0.
+ };
+ */
+ Double_t secX2[ksecNRadii];
+ Double_t secY2[ksecNRadii];
+ Double_t secR2[ksecNRadii] = {
+ ksecR0, ksecR1, ksecRCoolOut,
+ ksecR2, ksecR3, ksecRCoolOut,
+ ksecR4, ksecR5, ksecRCoolOut,
+ ksecR6, ksecR7, ksecRCoolOut,
+ ksecR8, ksecR9, ksecRCoolOut,
+ ksecR10, ksecR11, ksecRCoolOut,
+ ksecR12, ksecR13
+ };
+ Double_t secDip2[ksecNCoolingTubeDips] = {
+ ksecDl1, ksecDl2, ksecDl3,
+ ksecDl4, ksecDl5, ksecDl6
+ };
+ Double_t secX3[ksecNRadii];
+ Double_t secY3[ksecNRadii];
+ const Int_t ksecDipIndex[ksecNCoolingTubeDips] = {2, 5, 8, 11, 14, 17};
Double_t secAngleStart[ksecNRadii];
Double_t secAngleEnd[ksecNRadii];
- Double_t secAngleStart2[ksecNRadii+ksecNCoolingTubeDips];
- Double_t secAngleEnd2[ksecNRadii+ksecNCoolingTubeDips];
- Double_t secAngleStart3[ksecNRadii+ksecNCoolingTubeDips];
- Double_t secAngleEnd3[ksecNRadii+ksecNCoolingTubeDips];
- Double_t xp[ksecNPoints],yp[ksecNPoints];
- TGeoXtru *sA0,*sA1,*sB0,*sB1;
- TGeoEltu *sTA0,*sTA1;
- TGeoTube *sTB0,*sTB1;
+ Double_t secAngleStart2[ksecNRadii];
+ Double_t secAngleEnd2[ksecNRadii];
+ Double_t secAngleTurbo[ksecNCoolingTubeDips] = {0., 0., 0., 0., 0., 0.0};
+ //Double_t secAngleStart3[ksecNRadii];
+ //Double_t secAngleEnd3[ksecNRadii];
+ Double_t xpp[ksecNPoints], ypp[ksecNPoints];
+ Double_t xpp2[ksecNPoints], ypp2[ksecNPoints];
+ Double_t *xp[ksecNRadii], *xp2[ksecNRadii];
+ Double_t *yp[ksecNRadii], *yp2[ksecNRadii];
+ TGeoXtru *sA0, *sA1, *sB0, *sB1,*sB2;
+ TGeoBBox *sB3;
+ TGeoEltu *sTA0, *sTA1;
+ TGeoTube *sTB0, *sTB1; //,*sM0;
TGeoRotation *rot;
TGeoTranslation *trans;
TGeoCombiTrans *rotrans;
- Double_t t,t0,t1,a,b,x0,y0,x1,y1;
- Int_t i,j,k;
+ Double_t t, t0, t1, a, b, x0, y0,z0, x1, y1;
+ Int_t i, j, k, m;
+ Bool_t tst;
- if(moth==0){
- Error("CarbonFiberSector","moth=%p",moth);
+ if(!moth) {
+ AliError("Container volume (argument) is NULL");
return;
- } // end if moth==0
- SetDebug(3);
-
- secAngleStart[0] = 0.5*ksecAngleSide13;
- for(i=0;i<ksecNRadii-2;i++){
- AnglesForRoundedCorners(secX[i],secY[i],secR[i],
- secX[i+1],secY[i+1],secR[i+1],t0,t1);
- secAngleEnd[i] = t0;
- if(secR[i]>0.0&&secR[i+1]>0.0)if(secAngleStart[i]>secAngleEnd[i])
- secAngleEnd[i] += 360.0;
- secAngleStart[i+1] = t1;
- } // end for i
- secAngleEnd[ksecNRadii-2] = secAngleStart[ksecNRadii-2] +
- (secAngleEnd[10]-secAngleStart[10]);
- if(secAngleEnd[ksecNRadii-2]<0.0) secAngleEnd[ksecNRadii-2] += 360.0;
- secAngleStart[ksecNRadii-1] = secAngleEnd[ksecNRadii-2] - 180.0;
- secAngleEnd[ksecNRadii-1] = secAngleStart[0];
+ } // end if(!moth)
+ for(i = 0; i < ksecNRadii; i++) {
+ xp[i] = &(xpp[i*(ksecNPointsPerRadii+1)]);
+ yp[i] = &(ypp[i*(ksecNPointsPerRadii+1)]);
+ xp2[i] = &(xpp2[i*(ksecNPointsPerRadii+1)]);
+ yp2[i] = &(ypp2[i*(ksecNPointsPerRadii+1)]);
+ secX2[i] = secX[i];
+ secY2[i] = secY[i];
+ secX3[i] = secX[i];
+ secY3[i] = secY[i];
+ } // end for i
+ //
+ // find starting and ending angles for all but cooling tube sections
+ secAngleStart[0] = 0.5 * ksecAngleSide13;
+ for(i = 0; i < ksecNRadii - 2; i++) {
+ tst = kFALSE;
+ for(j=0;j<ksecNCoolingTubeDips;j++) tst = (tst||i==ksecDipIndex[j]);
+ if (tst) continue;
+ tst = kFALSE;
+ for(j=0;j<ksecNCoolingTubeDips;j++) tst =(tst||(i+1)==ksecDipIndex[j]);
+ if (tst) j = i+2; else j = i+1;
+ AnglesForRoundedCorners(secX[i],secY[i],secR[i],secX[j],secY[j],
+ secR[j],t0,t1);
+ secAngleEnd[i] = t0;
+ secAngleStart[j] = t1;
+ if(secR[i] > 0.0 && secR[j] > 0.0) {
+ if(secAngleStart[i] > secAngleEnd[i]) secAngleEnd[i] += 360.0;
+ } // end if(secR[i]>0.0 && secR[j]>0.0)
+ secAngleStart2[i] = secAngleStart[i];
+ secAngleEnd2[i] = secAngleEnd[i];
+ } // end for i
+ secAngleEnd[ksecNRadii-2] = secAngleStart[ksecNRadii-2] +
+ (secAngleEnd[ksecNRadii-5] - secAngleStart[ksecNRadii-5]);
+ if (secAngleEnd[ksecNRadii-2] < 0.0) secAngleEnd[ksecNRadii-2] += 360.0;
+ secAngleStart[ksecNRadii-1] = secAngleEnd[ksecNRadii-2] - 180.0;
+ secAngleEnd[ksecNRadii-1] = secAngleStart[0];
+ secAngleStart2[ksecNRadii-2] = secAngleStart[ksecNRadii-2];
+ secAngleEnd2[ksecNRadii-2] = secAngleEnd[ksecNRadii-2];
+ secAngleStart2[ksecNRadii-1] = secAngleStart[ksecNRadii-1];
+ secAngleEnd2[ksecNRadii-1] = secAngleEnd[ksecNRadii-1];
//
+ // find location of circle last rounded corner.
i = 0;
- j = ksecNRadii-2;
+ j = ksecNRadii - 2;
t0 = TanD(secAngleStart[i]-90.);
t1 = TanD(secAngleEnd[j]-90.);
t = secY[i] - secY[j];
- // Note, secR[i=0] <0; secR[j=12]>0; and secR[j+1=13] <0
- t += (-secR[i]+secR[j+1])*SinD(secAngleStart[i]);
- t -= (secR[j]-secR[j+1])*SinD(secAngleEnd[j]);
- t += t1*secX[j] - t0*secX[i];
- t += t1*(secR[j]-secR[j+1])*CosD(secAngleEnd[j]);
- t -= t0*(-secR[i]+secR[j+1])*CosD(secAngleStart[i]);
- secX[ksecNRadii-1] = t/(t1-t0);
- secY[ksecNRadii-1] = TanD(90.+0.5*ksecAngleSide13)*
- (secX[ksecNRadii-1]-secX[0]) + secY[0];
- //
- if(AliDebugLevel()>=2){
- cout <<" X \t Y \t R \t S \t E"<<endl;
- for(i=0;i<ksecNRadii;i++){
- cout <<"{"<< secX[i] <<",";
- cout << secY[i] <<",";
- cout << secR[i] <<",";
- cout << secAngleStart[i] <<",";
- cout << secAngleEnd[i] <<"},"<< endl;
- } // end for i
- } // end if GetDebug
- //
- if(GetDebug(3)) cout <<"Double_t sA0[][";
- if(GetDebug(4)) cout <<"3]{";
- else if(GetDebug(3)) cout <<"2]{";
- j = -1;
- t0 = (Double_t)ksecNPointsPerRadii;
- for(i=0;i<ksecNRadii;i++){
- t1 = (secAngleEnd[i]-secAngleStart[i])/t0;
- if(GetDebug(5)) cout<<"t1="<< t1<<endl;
- for(k=0;k<=ksecNPointsPerRadii;k++){
- t=secAngleStart[i]+((Double_t)k)*t1;
- j++;
- xp[j] = TMath::Abs(secR[i])*CosD(t)+secX[i];
- yp[j] = TMath::Abs(secR[i])*SinD(t)+secY[i];
- if(GetDebug(3)){
- cout << "{"<<xp[j]<<","<<yp[j];
- if(GetDebug(4)) cout <<","<<t;
- cout <<"},";
- } // end if GetDebug
+ // NOTE: secR[i=0] < 0; secR[j=18] > 0; and secR[j+1=19] < 0
+ t += (-secR[i]+secR[j+1]) * SinD(secAngleStart[i]);
+ t -= (secR[j]-secR[j+1]) * SinD(secAngleEnd[j]);
+ t += t1 * secX[j] - t0*secX[i];
+ t += t1 * (secR[j] - secR[j+1]) * CosD(secAngleEnd[j]);
+ t -= t0 * (-secR[i]+secR[j+1]) * CosD(secAngleStart[i]);
+ secX[ksecNRadii-1] = t / (t1-t0);
+ secY[ksecNRadii-1] = TanD(90.0+0.5*ksecAngleSide13)*
+ (secX[ksecNRadii-1]-secX[0])+secY[0];
+ secX2[ksecNRadii-1] = secX[ksecNRadii-1];
+ secY2[ksecNRadii-1] = secY[ksecNRadii-1];
+ secX3[ksecNRadii-1] = secX[ksecNRadii-1];
+ secY3[ksecNRadii-1] = secY[ksecNRadii-1];
+
+ // find location of cooling tube centers
+ for(i = 0; i < ksecNCoolingTubeDips; i++) {
+ j = ksecDipIndex[i];
+ x0 = secX[j-1] + TMath::Abs(secR[j-1]) * CosD(secAngleEnd[j-1]);
+ y0 = secY[j-1] + TMath::Abs(secR[j-1]) * SinD(secAngleEnd[j-1]);
+ x1 = secX[j+1] + TMath::Abs(secR[j+1]) * CosD(secAngleStart[j+1]);
+ y1 = secY[j+1] + TMath::Abs(secR[j+1]) * SinD(secAngleStart[j+1]);
+ t0 = TMath::Sqrt((x0-x1)*(x0-x1)+(y0-y1)*(y0-y1));
+ t = secDip2[i] / t0;
+ a = x0+(x1-x0) * t;
+ b = y0+(y1-y0) * t;
+ if(i == 0) {
+ // get location of tube center->Surface for locating
+ // this sector around the beam pipe.
+ // This needs to be double checked, but I need my notes for that.
+ // (Bjorn Nilsen)
+ xAAtubeCenter0 = x0 + (x1 - x0) * t * 0.5;
+ yAAtubeCenter0 = y0 + (y1 - y0) * t * 0.5;
+ }// end if i==0
+ if(a + b*(a - x0) / (b - y0) > 0.0) {
+ secX[j] = a + TMath::Abs(y1-y0) * 2.0 * ksecDipRadii/t0;
+ secY[j] = b - TMath::Sign(2.0*ksecDipRadii,y1-y0) * (x1-x0)/t0;
+ secX2[j] = a + TMath::Abs(y1-y0) * ksecTl/t0;
+ secY2[j] = b - TMath::Sign(ksecTl,y1-y0) * (x1-x0) / t0;
+ secX3[j] = a + TMath::Abs(y1-y0) *
+ (2.0*ksecDipRadii-0.5*ksecCoolTubeFlatY)/t0;
+ secY3[j] = b - TMath::Sign(2.0*ksecDipRadii-0.5*ksecCoolTubeFlatY,
+ y1-y0)*(x1-x0)/t0;
+ } else {
+ secX[j] = a - TMath::Abs(y1-y0)*2.0*ksecDipRadii/t0;
+ secY[j] = b + TMath::Sign(2.0*ksecDipRadii,y1-y0)*(x1-x0)/t0;
+ secX2[j] = a - TMath::Abs(y1-y0)*ksecTl/t0;
+ secY2[j] = b + TMath::Sign(ksecTl,y1-y0)*(x1-x0)/t0;
+ secX3[j] = a - TMath::Abs(y1-y0)*(2.0*ksecDipRadii-0.5*
+ ksecCoolTubeFlatY)/t0;
+ secY3[j] = b + TMath::Sign(2.0*ksecDipRadii-0.5*ksecCoolTubeFlatY,
+ y1-y0)*(x1-x0)/t0;
+ } // end if(a+b*(a-x0)/(b-y0)>0.0)
+
+ // Set up Start and End angles to correspond to start/end of dips.
+ t1 = (secDip2[i]-TMath::Abs(secR[j])) / t0;
+ secAngleStart[j] =TMath::RadToDeg()*TMath::ATan2(y0+(y1-y0)*t1-secY[j],
+ x0+(x1-x0)*t1-secX[j]);
+ if (secAngleStart[j]<0.0) secAngleStart[j] += 360.0;
+ secAngleStart2[j] = secAngleStart[j];
+ t1 = (secDip2[i]+TMath::Abs(secR[j]))/t0;
+ secAngleEnd[j] = TMath::RadToDeg()*TMath::ATan2(y0+(y1-y0)*t1-secY[j],
+ x0+(x1-x0)*t1-secX[j]);
+ if (secAngleEnd[j]<0.0) secAngleEnd[j] += 360.0;
+ secAngleEnd2[j] = secAngleEnd[j];
+ if (secAngleEnd[j]>secAngleStart[j]) secAngleEnd[j] -= 360.0;
+ secR[j] = TMath::Sqrt(secR[j]*secR[j]+4.0*ksecDipRadii*ksecDipRadii);
+ } // end for i
+
+ // Special cases
+ secAngleStart2[8] -= 360.;
+ secAngleStart2[11] -= 360.;
+
+ SPDsectorShape(ksecNRadii, secX, secY, secR, secAngleStart, secAngleEnd,
+ ksecNPointsPerRadii, m, xp, yp);
+
+ // Fix up dips to be square.
+ for(i = 0; i < ksecNCoolingTubeDips; i++) {
+ j = ksecDipIndex[i];
+ t = 0.5*ksecDipLength+ksecDipRadii;
+ t0 = TMath::RadToDeg()*TMath::ATan(2.0*ksecDipRadii/t);
+ t1 = secAngleEnd[j] + t0;
+ t0 = secAngleStart[j] - t0;
+ x0 = xp[j][1] = secX[j] + t*CosD(t0);
+ y0 = yp[j][1] = secY[j] + t*SinD(t0);
+ x1 = xp[j][ksecNPointsPerRadii-1] = secX[j] + t*CosD(t1);
+ y1 = yp[j][ksecNPointsPerRadii-1] = secY[j] + t*SinD(t1);
+ t0 = 1./((Double_t)(ksecNPointsPerRadii-2));
+ for(k = 2; k < ksecNPointsPerRadii - 1; k++) {
+ // extra points spread them out.
+ t = ((Double_t)(k-1)) * t0;
+ xp[j][k] = x0+(x1-x0) * t;
+ yp[j][k] = y0+(y1-y0) * t;
} // end for k
- if(GetDebug(3)) cout << endl;
- t = secAngleEnd[i];
- a = ksecDipLength+2.0*(ksecDipRadii);
- b = secDip[i]-0.5*a;
- switch (i){
- case 1: case 5: // Dip0,2
- j++;
- xp[j] = xp[j-1]-b*CosD(t-90.);
- yp[j] = yp[j-1]-b*SinD(t-90.);
- j++;
- xp[j] = xp[j-1]-(2.0*ksecDipRadii)*CosD(t);
- yp[j] = yp[j-1]-(2.0*ksecDipRadii)*SinD(t);
- j++;
- xp[j] = xp[j-1]-a*CosD(t-90.);
- yp[j] = yp[j-1]-a*SinD(t-90.);
- j++;
- xp[j] = xp[j-1]+(2.0*ksecDipRadii)*CosD(t);
- yp[j] = yp[j-1]+(2.0*ksecDipRadii)*SinD(t);
- if(GetDebug(3))for(k=-3;k<=0;k++){
- cout << "{"<<xp[j+k]<<","<<yp[j+k];
- if(GetDebug(4)) cout <<","<<0.0;
- cout <<"},";
- } // end if GetDebug
- if(GetDebug(3)) cout << endl;
- break;
- case 3: case 7: case 9: case 11:// Dip 1,3,4,5
- j++;
- xp[j] = xp[j-1]+b*CosD(t-90.);
- yp[j] = yp[j-1]+b*SinD(t-90.);
- j++;
- xp[j] = xp[j-1]+(2.0*ksecDipRadii)*CosD(t);
- yp[j] = yp[j-1]+(2.0*ksecDipRadii)*SinD(t);
- j++;
- xp[j] = xp[j-1]+a*CosD(t-90.);
- yp[j] = yp[j-1]+a*SinD(t-90.);
- j++;
- xp[j] = xp[j-1]-(2.0*ksecDipRadii)*CosD(t);
- yp[j] = yp[j-1]-(2.0*ksecDipRadii)*SinD(t);
- if(GetDebug(3))for(k=-3;k<=0;k++){
- cout << "{"<<xp[j+k]<<","<<yp[j+k];
- if(GetDebug(4)) cout <<","<<0.0;
- cout <<"},";
- } // end if GetDebug
- if(GetDebug(3)) cout << endl;
- break;
- default:
- break;
- } // end switch
- } // end of i
- if(GetDebug(3)) cout<<"{"<<xp[0]<<","<<yp[0];
- if(GetDebug(4)) cout<<","<< secAngleStart[0];
- if(GetDebug(3)) cout<<"}} j="<<j<<endl;
+ secAngleTurbo[i] = -TMath::RadToDeg() * TMath::ATan2(y1-y0, x1-x0);
+ if(GetDebug(3)) {
+ AliInfo(
+ Form("i=%d -- angle=%f -- x0,y0=(%f, %f) -- x1,y1=(%f, %f)",
+ i, secAngleTurbo[i], x0, y0, x1, y1));
+ } // end if GetDebug(3)
+ } // end for i
sA0 = new TGeoXtru(2);
sA0->SetName("ITS SPD Carbon fiber support Sector A0");
- sA0->DefinePolygon(j+1,xp,yp);
- sA0->DefineSection(0,-ksecDz);
- sA0->DefineSection(1,ksecDz);
- //
- if(GetDebug(3)) cout <<"Double_t sA1[][{";
- if(GetDebug(4)) cout <<"3]{";
- else if(GetDebug(3)) cout <<"2]{";
- j = -1;
- t0 = (Double_t)ksecNPointsPerRadii;
- for(i=0;i<ksecNRadii;i++){
- t1 = (secAngleEnd[i]-secAngleStart[i])/t0;
- if(GetDebug(5)) cout<<"t1="<< t1<<endl;
- for(k=0;k<=ksecNPointsPerRadii;k++){
- t=secAngleStart[i]+((Double_t)k)*t1;
- j++;
- xp[j] = TMath::Abs(secR[i]-ksecCthick)*CosD(t)+secX[i];
- yp[j] = TMath::Abs(secR[i]-ksecCthick)*SinD(t)+secY[i];
- if(GetDebug(3)){
- cout << "{"<<xp[j]<<","<<yp[j];
- if(GetDebug(4)) cout <<","<<t;
- cout <<"},";
- } // end if GetDebug
- } // end for t
- if(GetDebug(3)) cout << endl;
- t = secAngleEnd[i];
- a = ksecDipLength+2.0*(ksecDipRadii+ksecCthick);
- b = secDip[i]-0.5*a;
- switch (i){
- case 1: case 5: // Dip0,2
- j++;
- xp[j] = xp[j-1]-b*CosD(t-90.);
- yp[j] = yp[j-1]-b*SinD(t-90.);
- j++;
- xp[j] = xp[j-1]-(2.0*ksecDipRadii)*CosD(t);
- yp[j] = yp[j-1]-(2.0*ksecDipRadii)*SinD(t);
- j++;
- xp[j] = xp[j-1]-a*CosD(t-90.);
- yp[j] = yp[j-1]-a*SinD(t-90.);
- j++;
- xp[j] = xp[j-1]+(2.0*ksecDipRadii)*CosD(t);
- yp[j] = yp[j-1]+(2.0*ksecDipRadii)*SinD(t);
- if(GetDebug(3))for(k=-3;k<=0;k++){
- cout << "{"<<xp[j+k]<<","<<yp[j+k];
- if(GetDebug(4)) cout <<",t="<<0.0;
- cout <<"},";
- } // end if GetDebug
- if(GetDebug(3)) cout << endl;
- break;
- case 3: case 7: case 9: case 11:// Dip 1,3,4,5
- j++;
- xp[j] = xp[j-1]+b*CosD(t-90.);
- yp[j] = yp[j-1]+b*SinD(t-90.);
- j++;
- xp[j] = xp[j-1]+(2.0*ksecDipRadii)*CosD(t);
- yp[j] = yp[j-1]+(2.0*ksecDipRadii)*SinD(t);
- j++;
- xp[j] = xp[j-1]+a*CosD(t-90.);
- yp[j] = yp[j-1]+a*SinD(t-90.);
- j++;
- xp[j] = xp[j-1]-(2.0*ksecDipRadii)*CosD(t);
- yp[j] = yp[j-1]-(2.0*ksecDipRadii)*SinD(t);
- if(GetDebug(3))for(k=-3;k<=0;k++){
- cout << "{"<<xp[j+k]<<","<<yp[j+k];
- if(GetDebug(4)) cout <<",t="<<0.0;
- cout <<"},";
- } // end if GetDebug
- if(GetDebug(3)) cout << endl;
- break;
- default:
- break;
- } // end switch
- } // end of i
- if(GetDebug(3)) cout<<"{"<<xp[0]<<","<<yp[0];
- if(GetDebug(4)) cout<<","<< secAngleStart[0];
- if(GetDebug(3)) cout<<"}} j="<<j<<endl;
+ sA0->DefinePolygon(m, xpp, ypp);
+ sA0->DefineSection(0, -ksecDz);
+ sA0->DefineSection(1, ksecDz);
+
+ // store the edges of each XY segment which defines
+ // one of the plane zones where staves will have to be placed
+ fSPDsectorX0.Set(ksecNCoolingTubeDips);
+ fSPDsectorY0.Set(ksecNCoolingTubeDips);
+ fSPDsectorX1.Set(ksecNCoolingTubeDips);
+ fSPDsectorY1.Set(ksecNCoolingTubeDips);
+ Int_t ixy0, ixy1;
+ for(i = 0; i < ksecNCoolingTubeDips; i++) {
+ // Find index in xpp[] and ypp[] corresponding to where the
+ // SPD ladders are to be attached. Order them according to
+ // the ALICE numbering schema. Using array of indexes (+-1 for
+ // cooling tubes. For any "bend/dip/edge, there are
+ // ksecNPointsPerRadii+1 points involved.
+ if(i == 0) j = 1;
+ else if (i == 1) j = 0;
+ else j = i;
+ ixy0 = (ksecDipIndex[j]-1)*(ksecNPointsPerRadii+1)+
+ (ksecNPointsPerRadii);
+ ixy1 = (ksecDipIndex[j]+1) * (ksecNPointsPerRadii+1);
+ fSPDsectorX0[i] = sA0->GetX(ixy0);
+ fSPDsectorY0[i] = sA0->GetY(ixy0);
+ fSPDsectorX1[i] = sA0->GetX(ixy1);
+ fSPDsectorY1[i] = sA0->GetY(ixy1);
+ } // end for i
+
+ //printf("SectorA#%d ",0);
+ InsidePoint(xpp[m-1],ypp[m-1],xpp[0],ypp[0],xpp[1],ypp[1],ksecCthick,
+ xpp2[0],ypp2[0]);
+ for(i = 1; i < m - 1; i++) {
+ j = i / (ksecNPointsPerRadii+1);
+ //printf("SectorA#%d ",i);
+ InsidePoint(xpp[i-1],ypp[i-1],xpp[i],ypp[i],xpp[i+1],ypp[i+1],
+ ksecCthick,xpp2[i],ypp2[i]);
+ } // end for i
+ //printf("SectorA#%d ",m);
+ InsidePoint(xpp[m-2],ypp[m-2],xpp[m-1],ypp[m-1],xpp[0],ypp[0],
+ ksecCthick,xpp2[m-1],ypp2[m-1]);
+ // Fix center value of cooling tube dip and
+ // find location of cooling tube centers
+ for(i = 0; i < ksecNCoolingTubeDips; i++) {
+ j = ksecDipIndex[i];
+ x0 = xp2[j][1];
+ y0 = yp2[j][1];
+ x1 = xp2[j][ksecNPointsPerRadii-1];
+ y1 = yp2[j][ksecNPointsPerRadii-1];
+ t0 = TMath::Sqrt((x0-x1)*(x0-x1)+(y0-y1)*(y0-y1));
+ t = secDip2[i]/t0;
+ for(k = 2; k < ksecNPointsPerRadii - 1; k++) {
+ // extra points spread them out.
+ t = ((Double_t)(k-1)) * t0;
+ xp2[j][k] = x0+(x1-x0) * t;
+ yp2[j][k] = y0+(y1-y0) * t;
+ } // end for k
+ } // end for i
sA1 = new TGeoXtru(2);
sA1->SetName("ITS SPD Carbon fiber support Sector Air A1");
- sA1->DefinePolygon(j+1,xp,yp);
- sA1->DefineSection(0,-ksecDz);
- sA1->DefineSection(1,ksecDz);
+ sA1->DefinePolygon(m, xpp2, ypp2);
+ sA1->DefineSection(0, -ksecDz);
+ sA1->DefineSection(1, ksecDz);
//
- sTA0 = new TGeoEltu("ITS SPD Cooling Tube TA0",
- ksecDipRadii,0.5*ksecDipLength,ksecDz);
+ // Error in TGeoEltu. Semi-axis X must be < Semi-axis Y (?).
+ sTA0 = new TGeoEltu("ITS SPD Cooling Tube TA0", 0.5 * ksecCoolTubeFlatY,
+ 0.5 * ksecCoolTubeFlatX, ksecDz);
sTA1 = new TGeoEltu("ITS SPD Cooling Tube coolant TA1",
- sTA0->GetA()-ksecCoolTubeThick,
+ sTA0->GetA() - ksecCoolTubeThick,
sTA0->GetB()-ksecCoolTubeThick,ksecDz);
- //
- j = 0;
- for(i=0;i<ksecNRadii;i++){
- secAngleStart2[j] = secAngleStart[i];
- secAngleEnd2[j] = secAngleEnd[i];
- secAngleStart3[j] = secAngleStart2[j];
- secAngleEnd3[j] = secAngleEnd2[j];
- secX2[j] = secX[i];
- secY2[j] = secY[i];
- secR2[j] = secR[i];
- j++;
- t = secAngleEnd[i];
- switch (i){
- case 1: case 5: // Tube 0,2
- x0 = secX[i] + TMath::Abs(secR[i])*CosD(t); // last point of turn
- y0 = secY[i] + TMath::Abs(secR[i])*SinD(t);
- x1 = x0-secDip2[i]*CosD(t-90.); // center point of dip
- y1 = y0-secDip2[i]*SinD(t-90.); // along line
- secX2[j] = x1-ksecTl*CosD(t); // location of circle center.
- secY2[j] = y1-ksecTl*SinD(t);
- x1 = secX[i+1]+TMath::Abs(secR[i+1])*CosD(secAngleStart2[i+1]);
- y1 = secY[i+1]+TMath::Abs(secR[i+1])*SinD(secAngleStart2[i+1]);
- //Find starting and ending angles, break if error.
- if(!AngleOfIntersectionWithLine(x0,y0,x1,y1,secX2[j],secY2[j],
- secR2[j],secAngleStart2[j],secAngleEnd2[j]))break;
- // thicknes of Carbon fiber over the cooling tubes.
- a = ksecRCoolOut-ksecRCoolIn;
- // last point of turn
- x0 = secX[i]+(TMath::Abs(secR[i])-ksecCthick2)*CosD(t);
- y0 = secY[i]+(TMath::Abs(secR[i])-ksecCthick2)*SinD(t);
- x1 = secX[i+1]+(TMath::Abs(secR[i+1])-ksecCthick2)*CosD(secAngleStart3[i+1]);
- y1 = secY[i+1]+(TMath::Abs(secR[i+1])-ksecCthick2)*SinD(secAngleStart3[i+1]);
- //Find starting and ending angles, break if error.
- if(!AngleOfIntersectionWithLine(x0,y0,x1,y1,secX2[j],secY2[j],
- secR2[j]-a,secAngleStart3[j],secAngleEnd3[j]))break;
- if(i==1) { // Fix odd case.
- x0 = secAngleStart3[j];
- secAngleStart3[j] = secAngleEnd3[j] - 360.0;
- secAngleEnd3[j] = x0;
- } // end if i==1
- if(i==5) { // Fix odd case.
- x0 = secAngleStart2[j];
- secAngleStart2[j] = secAngleEnd2[j] - 360.0;
- secAngleEnd2[j] = x0;
- x0 = secAngleStart3[j];
- secAngleStart3[j] = secAngleEnd3[j] - 360.0;
- secAngleEnd3[j] = x0;
- } // end if i==5
- // Because a polygon is replacing the rounded surface, the
- // radius of the polygon must be larger to make room for the
- // cooling tube of the same size. The radio of the radii of
- // a circle fitting the inside/outside of a regualr polygon
- // is given by Cos(180/n) where n is the number of sides of the
- // regurla polygon. In this case, it is scalled for the partical
- // circles involved.
- secR2[j] = secR2[j]/CosD(0.5*(secAngleEnd[j]-secAngleStart[j])/
- ((Double_t)ksecNPointsPerRadii));
- j++;
- break;
- case 3: case 7: case 9: case 11:// Tube 1,2,4,5,6
- x0 = secX[i] + TMath::Abs(secR[i])*CosD(t); // last point of turn
- y0 = secY[i] + TMath::Abs(secR[i])*SinD(t);
- x1 = x0+secDip2[i]*CosD(t-90.); // center point of dip
- y1 = y0+secDip2[i]*SinD(t-90.); // along line
- secX2[j] = x1+ksecTl*CosD(t); // location of circle center.
- secY2[j] = y1+ksecTl*SinD(t);
- x1 = secX[i+1]+TMath::Abs(secR[i+1])*CosD(secAngleStart2[i+1]);
- y1 = secY[i+1]+TMath::Abs(secR[i+1])*SinD(secAngleStart2[i+1]);
- if(!AngleOfIntersectionWithLine(x0,y0,x1,y1,secX2[j],secY2[j],
- secR2[j],secAngleStart2[j],secAngleEnd2[j]))break;//don't intersect
- // thicknes of Carbon fiber over the cooling tubes.
- a = ksecRCoolOut-ksecRCoolIn;
- // last point of turn
- x0 = secX[i] + (TMath::Abs(secR[i])+ksecCthick2)*CosD(t);
- y0 = secY[i] + (TMath::Abs(secR[i])+ksecCthick2)*SinD(t);
- x1 = secX[i+1]+(TMath::Abs(secR[i+1])-ksecCthick2)*CosD(secAngleStart3[i+1]);
- y1 = secY[i+1]+(TMath::Abs(secR[i+1])-ksecCthick2)*SinD(secAngleStart3[i+1]);
- //Find starting and ending angles, break if error.
- if(!AngleOfIntersectionWithLine(x0,y0,x1,y1,secX2[j],secY2[j],
- secR2[j]-a,secAngleStart3[j],secAngleEnd3[j]))break;
- if(i==7) { // Fix odd case
- x0 = secAngleStart2[j];
- secAngleStart2[j] = secAngleEnd2[j] - 360.0;
- secAngleEnd2[j] = x0;
- x0 = secAngleStart3[j];
- secAngleStart3[j] = secAngleEnd3[j] - 360.0;
- secAngleEnd3[j] = x0;
- } // end if i==7
- if(i==9) { // Fix odd case
- x0 = secAngleStart3[j];
- secAngleStart3[j] = secAngleEnd3[j] - 360.0;
- secAngleEnd3[j] = x0;
- } // end if i==7
- // Because a polygon is replacing the rounded surface, the
- // radius of the polygon must be larger to make room for the
- // cooling tube of the same size. The radio of the radii of
- // a circle fitting the inside/outside of a regualr polygon
- // is given by Cos(180/n) where n is the number of sides of the
- // regurla polygon. In this case, it is scalled for the partical
- // circles involved.
- secR2[j] = secR2[j]/CosD(0.5*(secAngleEnd[j]-secAngleStart[j])/
- ((Double_t)ksecNPointsPerRadii));
- j++;
- break;
- }// end switch
- } // end for i
- //
- if(GetDebug(2)){
- cout <<" X2 \t Y2 \t R2 \t S2 \t E2"<<endl;
- for(i=0;i<j;i++){
- cout <<"{"<< secX2[i] <<",";
- cout << secY2[i] <<",";
- cout << secR2[i] <<",";
- cout << secAngleStart2[i] <<",";
- cout << secAngleEnd2[i] <<"}," << endl;
- } // end for i
- } // end if GetDebug
- if(GetDebug(2)){
- cout <<" X2 \t Y2 \t R2 \t S3 \t E3"<<endl;
- for(i=0;i<j;i++){
- cout <<"{"<< secX2[i] <<",";
- cout << secY2[i] <<",";
- cout << secR2[i] <<",";
- cout << secAngleStart3[i] <<",";
- cout << secAngleEnd3[i] <<"}," << endl;
- } // end for i
- } // end if GetDebug
- if(GetDebug(3)) cout <<"Double_t sB0[][";
- if(GetDebug(4)) cout <<"3]{";
- else if(GetDebug(3)) cout <<"2]{";
- j = -1;
- t0 = (Double_t)ksecNPointsPerRadii;
- for(i=0;i<ksecNRadii+ksecNCoolingTubeDips;i++){
- t1 = (secAngleEnd2[i]-secAngleStart2[i])/t0;
- if(GetDebug(5)) cout<<"t1="<< t1<<endl;
- for(k=0;k<=ksecNPointsPerRadii;k++){
- t=secAngleStart2[i]+((Double_t)k)*t1;
- j++;
- xp[j] = TMath::Abs(secR2[i])*CosD(t)+secX2[i];
- yp[j] = TMath::Abs(secR2[i])*SinD(t)+secY2[i];
- if(GetDebug(3)){
- cout << "{"<<xp[j]<<","<<yp[j];
- if(GetDebug(4)) cout <<","<<t;
- cout <<"},";
- } // end if GetDebug
- } // end for k
- if(GetDebug(3)) cout << endl;
- if(i==6) { // add thicker side
- b = CosD(0.5*ksecAngleSide13);
- a = SinD(0.5*ksecAngleSide13);
- x1 = xp[j];
- y1 = yp[j];
- x0 = a*a*ksecX5 + b*b*x1 - (y1-ksecY5)*a*b;
- y0 = a*a*y1 + b*b*ksecY5 - (x1-ksecX5)*a*b;
- j++;
- xp[j+3] = x0 - ksecSideD5*a;
- yp[j+3] = y0 - ksecSideD5*b;
- xp[j+2] = xp[j+3] + (ksecCthick3-ksecCthick2)*b;
- yp[j+2] = yp[j+3] - (ksecCthick3-ksecCthick2)*a;
- xp[j+1] = xp[j+2] - ksecSidelen*a;
- yp[j+1] = yp[j+2] - ksecSidelen*b;
- xp[j] = xp[j+1] - (ksecCthick3-ksecCthick2)*b;
- yp[j] = yp[j+1] + (ksecCthick3-ksecCthick2)*a;
- j += 3;
- if(GetDebug(3))for(k=-3;k<=0;k++){
- cout << "{"<<xp[j+k]<<","<<yp[j+k];
- if(GetDebug(4)) cout <<",t="<<0.0;
- cout <<"},";
- } // end if GetDebug
- if(GetDebug(3)) cout << endl;
- } // end if i==6
- if(i==19) { // add thicker side
- // first propogate referece point 12 to -18 degree edge
- b = CosD(0.5*ksecAngleSide13);
- a = SinD(0.5*ksecAngleSide13);
- x1 = secX[0]+TMath::Abs(secR[0])*CosD(secAngleStart[0]);
- y1 = secY[0]+TMath::Abs(secR[0])*SinD(secAngleStart[0]);
- x0 = a*b*(y1-secY[ksecNRadii-2]) +
- a*a*secX[ksecNRadii-2] + b*b*x1;
- y0 = a*b*(x1-secX[ksecNRadii-2]) +
- b*b*secY[ksecNRadii-2] + a*a*y1;
- j++;
- xp[j] = x0 + ksecSideD12*a;
- yp[j] = y0 - ksecSideD12*b;
- j++;
- xp[j] = xp[j-1] - (ksecCthick3-ksecCthick2)*b;
- yp[j] = yp[j-1] - (ksecCthick3-ksecCthick2)*a;
- j++;
- xp[j] = xp[j-1] + ksecSidelen*a;
- yp[j] = yp[j-1] - ksecSidelen*b;
- j++;
- xp[j] = xp[j-1] + (ksecCthick3-ksecCthick2)*b;
- yp[j] = yp[j-1] + (ksecCthick3-ksecCthick2)*a;
- if(GetDebug(3))for(k=-3;k<=0;k++){
- cout << "{"<<xp[j+k]<<","<<yp[j+k];
- if(GetDebug(4)) cout <<",t="<<0.0;
- cout <<"},";
- } // end if GetDebug
- if(GetDebug(3)) cout << endl;
- } // end if i==19
- } // end for i
- if(GetDebug(3)) cout<<"{"<<xp[0]<<","<<yp[0];
- if(GetDebug(4)) cout<<","<< secAngleStart2[0];
- if(GetDebug(3)) cout<<"}} j="<<j<<endl;
+ SPDsectorShape(ksecNRadii,secX2,secY2,secR2,secAngleStart2,secAngleEnd2,
+ ksecNPointsPerRadii, m, xp, yp);
sB0 = new TGeoXtru(2);
sB0->SetName("ITS SPD Carbon fiber support Sector End B0");
- sB0->DefinePolygon(j+1,xp,yp);
- sB0->DefineSection(0,ksecDz);
- sB0->DefineSection(1,ksecDz+ksecZEndLen);
- //
- if(GetDebug(3)) cout <<"Double_t sB1[][{";
- if(GetDebug(4)) cout <<"3]{";
- else if(GetDebug(3)) cout <<"2]{";
- j = -1;
- t0 = (Double_t)ksecNPointsPerRadii;
- for(i=0;i<ksecNRadii+ksecNCoolingTubeDips;i++){
- t1 = (secAngleEnd3[i]-secAngleStart3[i])/t0;
- if(GetDebug(5)) cout<<"t1="<< t1<<endl;
- for(k=0;k<=ksecNPointsPerRadii;k++){
- t=secAngleStart3[i]+((Double_t)k)*t1;
- j++;
- x0 = TMath::Abs(secR2[i]-ksecCthick2);
- if(i==2||i==5||i==8||i==11||i==14||i==17){
- x0 = TMath::Abs(secR2[i]-ksecRCoolOut+ksecRCoolIn);/*
- if(k==0){// compute change in start and end angles to
- // compensate for thickness of carbon fiber
- y0 = (ksecCthick2-ksecRCoolOut*SinD(t))/
- ksecRCoolIn; // sin th'
- if(GetDebug(5))cout <<" k=0 t="<<t<<" y0="<<y0<<endl;
- y1 = TMath::Sqrt(1-y0*y0); // cos th'
- t -= 180.*TMath::ASin(SinD(t)*y1-CosD(t)*y0)/TMath::Pi();
- }else if(k==ksecNPointsPerRadii) {
- y0 = (ksecCthick2-ksecRCoolOut*SinD(t))/
- ksecRCoolIn; // sin th'
- if(GetDebug(5))cout <<" k="<<k<<" t="<<t<<" y0="<<y0<<endl;
- y1 = TMath::Sqrt(1-y0*y0); // cos th'
- t += 180.*TMath::ASin(SinD(t)*y1-CosD(t)*y0)/TMath::Pi();
- } // end if
- */} // end if
- xp[j] = x0*CosD(t)+secX2[i];
- yp[j] = x0*SinD(t)+secY2[i];
- if(GetDebug(3)){
- cout << "{"<<xp[j]<<","<<yp[j];
- if(GetDebug(4)) cout <<","<<t;
- cout <<"},";
- } // end if GetDebug
- } // end for k
- if(GetDebug(3)) cout << endl;
- } // end for i
- if(GetDebug(3)) cout<<"{"<<xp[0]<<","<<yp[0];
- if(GetDebug(4)) cout<<","<< secAngleStart2[0];
- if(GetDebug(3)) cout<<"}} j="<<j<<endl;
+ sB0->DefinePolygon(m, xpp, ypp);
+ sB0->DefineSection(0, ksecDz);
+ sB0->DefineSection(1, ksecDz + ksecZEndLen);
+
+ //printf("SectorB#%d ",0);
+ // Points around the most sharpened tips have to be avoided - M.S. 24 feb 09
+ const Int_t nSpecialPoints = 5;
+ const Int_t kSpecialPoints[nSpecialPoints] = {7, 17, 47, 62, 77};
+ Int_t i2 = 0;
+ InsidePoint(xpp[m-1],ypp[m-1],xpp[0],ypp[0],xpp[1],ypp[1],
+ ksecCthick2,xpp2[i2],ypp2[i2]);
+ for(i = 1; i < m - 1; i++) {
+ t = ksecCthick2;
+ for(k = 0; k < ksecNCoolingTubeDips; k++)
+ if((i/(ksecNPointsPerRadii+1))==ksecDipIndex[k])
+ if(!(ksecDipIndex[k]*(ksecNPointsPerRadii+1) == i ||
+ ksecDipIndex[k]*(ksecNPointsPerRadii+1) +
+ ksecNPointsPerRadii == i))
+ t = ksecRCoolOut-ksecRCoolIn;
+ //printf("SectorB#%d ",i);
+ Bool_t useThisPoint = kTRUE;
+ for(Int_t ii = 0; ii < nSpecialPoints; ii++)
+ if ( (i == kSpecialPoints[ii] - 1) ||
+ (i == kSpecialPoints[ii] + 1) ) useThisPoint = kFALSE;
+ if (useThisPoint) {
+ i2++;
+ InsidePoint(xpp[i-1],ypp[i-1],xpp[i],ypp[i],xpp[i+1],ypp[i+1],t,
+ xpp2[i2],ypp2[i2]);
+ }
+ }// end for i
+ //printf("SectorB#%d ",m);
+ i2++;
+ InsidePoint(xpp[m-2],ypp[m-2],xpp[m-1],ypp[m-1],xpp[0],ypp[0],
+ ksecCthick2,xpp2[i2],ypp2[i2]);
sB1 = new TGeoXtru(2);
sB1->SetName("ITS SPD Carbon fiber support Sector Air End B1");
- sB1->DefinePolygon(j+1,xp,yp);
- sB1->DefineSection(0,ksecDz);
- sB1->DefineSection(1,ksecDz+ksecLen);
- sTB0 = new TGeoTube("ITS SPD Cooling Tube End TB0",0.0,
- ksecRCoolIn,0.5*ksecLen);
- sTB1 = new TGeoTube("ITS SPD Cooling Tube End coolant TB0",0.0,
- sTB0->GetRmax()-ksecCoolTubeThick,0.5*ksecLen);
- //
- if(GetDebug()){
+ sB1->DefinePolygon(i2+1, xpp2, ypp2);
+ sB1->DefineSection(0,sB0->GetZ(0));
+ sB1->DefineSection(1,sB0->GetZ(1)-ksecCthick2);
+ const Double_t kspdEndHoleRadius1=5.698*fgkmm;
+ const Double_t kspdEndHoleRadius2=2.336*fgkmm;
+ const Double_t kspdEndHoleDisplacement=6.29*fgkmm;
+ k = (m-1)/4;
+ for(i=0;i<=k;i++){
+ t= ((Double_t)i)/((Double_t)(k));
+ if(!CFHolePoints(t,kspdEndHoleRadius1,kspdEndHoleRadius2,
+ kspdEndHoleDisplacement,xpp2[i],ypp2[i])){
+ Warning("CarbonFiberSector","CFHolePoints failed "
+ "i=%d m=%d k=%d t=%e",i,m,k,t);
+ } // end if
+ // simitry in each quadrant.
+ xpp2[2*k-i] = -xpp2[i];
+ ypp2[2*k-i] = ypp2[i];
+ xpp2[2*k+i] = -xpp2[i];
+ ypp2[2*k+i] = -ypp2[i];
+ xpp2[4*k-i] = xpp2[i];
+ ypp2[4*k-i] = -ypp2[i];
+ }// end for i
+ //xpp2[m-1] = xpp2[0]; // begining point in
+ //ypp2[m-1] = ypp2[0]; // comment with end point
+ sB2 = new TGeoXtru(2);
+ sB2->SetName("ITS SPD Hole in Carbon fiber support End plate");
+ sB2->DefinePolygon(4*k, xpp2, ypp2);
+ sB2->DefineSection(0,sB1->GetZ(1));
+ sB2->DefineSection(1,sB0->GetZ(1));
+ // SPD sector mount blocks
+ const Double_t kMountBlock[3] = {0.5*(1.8-0.2)*fgkmm,0.5*22.0*fgkmm,
+ 0.5*45.0*fgkmm};
+ sB3 = new TGeoBBox((Double_t*)kMountBlock);
+ // SPD sector cooling tubes
+ sTB0 = new TGeoTube("ITS SPD Cooling Tube End TB0", 0.0,
+ 0.5*ksecCoolTubeROuter,0.5*(sB1->GetZ(1)-sB1->GetZ(0)));
+ sTB1 = new TGeoTube("ITS SPD Cooling Tube End coolant TB0", 0.0,
+ sTB0->GetRmax() - ksecCoolTubeThick,sTB0->GetDz());
+ //
+ if(GetDebug(3)) {
+ if(medSPDcf) medSPDcf->Dump(); else AliInfo("medSPDcf = 0");
+ if(medSPDss) medSPDss->Dump(); else AliInfo("medSPDss = 0");
+ if(medSPDair) medSPDair->Dump(); else AliInfo("medSPDAir = 0");
+ if(medSPDcoolfl) medSPDcoolfl->Dump();else AliInfo("medSPDcoolfl = 0");
sA0->InspectShape();
sA1->InspectShape();
sB0->InspectShape();
sB1->InspectShape();
- } // end if GetDebug
- //
- TGeoVolume *vM,*vA0,*vA1,*vTA0,*vTA1,*vB0,*vB1,*vTB0,*vTB1;
- vM = moth;
- vA0 = new TGeoVolume("ITSSPDCarbonFiberSupportSectorA0",sA0,medSPDcf);
+ sB2->InspectShape();
+ } // end if(GetDebug(3))
+
+ // create the assembly of the support and place staves on it
+ TGeoVolumeAssembly *vM0 = new TGeoVolumeAssembly(
+ "ITSSPDSensitiveVirtualvolumeM0");
+ StavesInSector(vM0);
+ // create other volumes with some graphical settings
+ TGeoVolume *vA0 = new TGeoVolume("ITSSPDCarbonFiberSupportSectorA0",
+ sA0, medSPDcf);
vA0->SetVisibility(kTRUE);
vA0->SetLineColor(4); // Blue
vA0->SetLineWidth(1);
vA0->SetFillColor(vA0->GetLineColor());
vA0->SetFillStyle(4010); // 10% transparent
- vA1 = new TGeoVolume("ITSSPDCarbonFiberSupportSectorAirA1",sA1,medSPDair);
+ TGeoVolume *vA1 = new TGeoVolume("ITSSPDCarbonFiberSupportSectorAirA1",
+ sA1, medSPDair);
vA1->SetVisibility(kTRUE);
vA1->SetLineColor(7); // light Blue
vA1->SetLineWidth(1);
vA1->SetFillColor(vA1->GetLineColor());
vA1->SetFillStyle(4090); // 90% transparent
- vTA0 = new TGeoVolume("ITSSPDCoolingTubeTA0",sTA0,medSPDss);
+ TGeoVolume *vTA0 = new TGeoVolume("ITSSPDCoolingTubeTA0", sTA0, medSPDss);
vTA0->SetVisibility(kTRUE);
- vTA0->SetLineColor(1); // Black
+ vTA0->SetLineColor(15); // gray
vTA0->SetLineWidth(1);
vTA0->SetFillColor(vTA0->GetLineColor());
vTA0->SetFillStyle(4000); // 0% transparent
- vTA1 = new TGeoVolume("ITSSPDCoolingTubeFluidTA1",sTA1,medSPDcoolfl);
+ TGeoVolume *vTA1 = new TGeoVolume("ITSSPDCoolingTubeFluidTA1",
+ sTA1, medSPDcoolfl);
vTA1->SetVisibility(kTRUE);
vTA1->SetLineColor(6); // Purple
vTA1->SetLineWidth(1);
vTA1->SetFillColor(vTA1->GetLineColor());
vTA1->SetFillStyle(4000); // 0% transparent
- vB0 = new TGeoVolume("ITSSPDCarbonFiberSupportSectorEndB0",sB0,medSPDcf);
+ TGeoVolume *vB0 = new TGeoVolume("ITSSPDCarbonFiberSupportSectorEndB0",
+ sB0, medSPDcf);
vB0->SetVisibility(kTRUE);
- vB0->SetLineColor(4); // Blue
+ vB0->SetLineColor(1); // Black
vB0->SetLineWidth(1);
vB0->SetFillColor(vB0->GetLineColor());
- vB0->SetFillStyle(4010); // 10% transparent
- vB1 = new TGeoVolume("ITSSPDCarbonFiberSupportSectorEndAirB1",sB1,medSPDair);
+ vB0->SetFillStyle(4000); // 0% transparent
+ TGeoVolume *vB1 = new TGeoVolume("ITSSPDCarbonFiberSupportSectorEndAirB1",
+ sB1, medSPDair);
vB1->SetVisibility(kTRUE);
- vB1->SetLineColor(7); // light Blue
+ vB1->SetLineColor(0); // white
vB1->SetLineWidth(1);
vB1->SetFillColor(vB1->GetLineColor());
- vB1->SetFillStyle(4090); // 90% transparent
- vTB0 = new TGeoVolume("ITSSPDCoolingTubeEndTB0",sTB0,medSPDss);
+ vB1->SetFillStyle(4100); // 100% transparent
+ TGeoVolume *vB2 = new TGeoVolume("ITSSPDCarbonFiberSupportSectorEndAirB2",
+ sB2, medSPDair);
+ vB2->SetVisibility(kTRUE);
+ vB2->SetLineColor(0); // white
+ vB2->SetLineWidth(1);
+ vB2->SetFillColor(vB2->GetLineColor());
+ vB2->SetFillStyle(4100); // 100% transparent
+ TGeoVolume *vB3 = new TGeoVolume(
+ "ITSSPDCarbonFiberSupportSectorMountBlockB3",sB3, medSPDcf);
+ vB3->SetVisibility(kTRUE);
+ vB3->SetLineColor(1); // Black
+ vB3->SetLineWidth(1);
+ vB3->SetFillColor(vB3->GetLineColor());
+ vB3->SetFillStyle(4000); // 0% transparent
+ TGeoVolume *vTB0 = new TGeoVolume("ITSSPDCoolingTubeEndTB0",sTB0,medSPDss);
vTB0->SetVisibility(kTRUE);
- vTB0->SetLineColor(1); // Black
+ vTB0->SetLineColor(15); // gray
vTB0->SetLineWidth(1);
vTB0->SetFillColor(vTB0->GetLineColor());
vTB0->SetFillStyle(4000); // 0% transparent
- vTB1 = new TGeoVolume("ITSSPDCoolingTubeEndFluidTB1",sTB1,medSPDcoolfl);
+ TGeoVolume *vTB1 = new TGeoVolume("ITSSPDCoolingTubeEndFluidTB1",sTB1,
+ medSPDcoolfl);
vTB1->SetVisibility(kTRUE);
- vTB1->SetLineColor(6); // Purple
+ vTB1->SetLineColor(7); // light blue
vTB1->SetLineWidth(1);
vTB1->SetFillColor(vTB1->GetLineColor());
- vTB1->SetFillStyle(4000); // 0% transparent
- //
+ vTB1->SetFillStyle(4050); // 0% transparent
+
+ // add volumes to mother container passed as argument of this method
+ moth->AddNode(vM0,1,0); // Add virtual volume to mother
vA0->AddNode(vA1,1,0); // Put air inside carbon fiber.
- vB0->AddNode(vB1,1,0); // Put air inside carbon fiber.
- vTA0->AddNode(vTA1,1,0); // Put air inside carbon fiber.
- vTB0->AddNode(vTB1,1,0); // Put air inside carbon fiber.
- for(i=0;i<ksecNCoolingTubeDips;i++){
- x0 = secX2[ksecDipIndex[i]];
- y0 = secY2[ksecDipIndex[i]];
- trans = new TGeoTranslation("",x0,y0,0.0);
- vB1->AddNode(vTB0,i+1,trans);
- rot = new TGeoRotation("",0.0,0.0,
- TMath::RadToDeg()*TMath::ATan2(y0,x0));
- rotrans = new TGeoCombiTrans(*trans,*rot);
- vM->AddNode(vTA0,i+1,rotrans);
- delete rot;
- } // end for i
- vM->AddNode(vA0,1,0);
- vM->AddNode(vB0,1,0);
- vM->AddNode(vB0,2,new TGeoScale(1.0,1.0,-1.0)); // Reflection.
- if(GetDebug()){
+ vB0->AddNode(vB1,1,0); // Put air inside carbon fiber ends.
+ vB0->AddNode(vB2,1,0); // Put air wholes inside carbon fiber ends
+ vTA0->AddNode(vTA1,1,0); // Put cooling liquid indide tube middel.
+ vTB0->AddNode(vTB1,1,0); // Put cooling liquid inside tube end.
+ Double_t tubeEndLocal[3]={0.0,0.0,sTA0->GetDz()};
+ for(i = 0; i < ksecNCoolingTubeDips; i++) {
+ x0 = secX3[ksecDipIndex[i]];
+ y0 = secY3[ksecDipIndex[i]];
+ t = 90.0 - secAngleTurbo[i];
+ trans = new TGeoTranslation("",x0,y0,0.5*(sB1->GetZ(0)+sB1->GetZ(1)));
+ vB1->AddNode(vTB0, i+1, trans);
+ // Find location of tube ends for later use.
+ trans->LocalToMaster(tubeEndLocal,fTubeEndSector[0][0][i]);
+ rot = new TGeoRotation("", 0.0, 0.0, t);
+ rotrans = new TGeoCombiTrans("", x0, y0, 0.0, rot);
+ vM0->AddNode(vTA0, i+1, rotrans);
+ } // end for i
+ vM0->AddNode(vA0, 1, 0);
+ vM0->AddNode(vB0, 1, 0);
+ // Reflection.
+ rot = new TGeoRotation("", 90., 0., 90., 90., 180., 0.);
+ vM0->AddNode(vB0,2,rot);
+ // Find location of tube ends for later use.
+ for(i=0;i<ksecNCoolingTubeDips;i++) rot->LocalToMaster(
+ fTubeEndSector[0][0][i],fTubeEndSector[0][1][i]);
+ // left side
+ t = -TMath::RadToDeg()*TMath::ATan2(
+ sB0->GetX(0)-sB0->GetX(sB0->GetNvert()-1),
+ sB0->GetY(0)-sB0->GetY(sB0->GetNvert()-1));
+ rot = new TGeoRotation("",t,0.0,0.0);// z axis rotation
+ x0 = 0.5*(sB0->GetX(0)+sB0->GetX(sB0->GetNvert()-1))+
+ sB3->GetDX()*TMath::Cos(t*TMath::DegToRad());
+ y0 = 0.5*(sB0->GetY(0)+sB0->GetY(sB0->GetNvert()-1))+
+ sB3->GetDX()*TMath::Sin(t*TMath::DegToRad());
+ z0 = sB0->GetZ(0)+sB3->GetDZ();
+ rotrans = new TGeoCombiTrans("",x0,y0,z0,rot);
+ vM0->AddNode(vB3,1,rotrans); // Put Mounting bracket on sector
+ rotrans = new TGeoCombiTrans("",x0,y0,-z0,rot);
+ vM0->AddNode(vB3,2,rotrans); // Put Mounting bracket on sector
+ /*
+ j = 0; // right side, find point with largest x value
+ x1 = sB0->GetX(0);
+ for(i=1;i<sB0->GetNvert();i++)if(sB0->GetX(i)>x1) {j=i;x1=sB0->GetX(i);}
+ j--; // Too big by 1
+ //t = -TMath::RadToDeg()*TMath::ATan2(
+ // sB0->GetX(j)-sB0->GetX(j-1),
+ // sB0->GetY(j)-sB0->GetY(j-1));
+ */
+ t *= -1.0;
+ rot = new TGeoRotation("",t,0.0,0.0); // z axis rotation
+ /* // this way gets correct orientation but wrong "height"
+ x0 = 0.5*(sB0->GetX(j)+sB0->GetX(j-1))+
+ sB3->GetDX()*TMath::Cos(t*TMath::DegToRad());
+ y0 = 0.5*(sB0->GetY(j)+sB0->GetY(j-1))+
+ sB3->GetDX()*TMath::Sin(t*TMath::DegToRad());
+ z0 = sB0->GetZ(0)+sB3->GetDZ();
+ */ // I don't understand the need for this factor 3.5.
+ // posibly the SPD sector as coded isn't symetric which the
+ // plans would suggest.
+ x0 = -0.5*(sB0->GetX(0)+sB0->GetX(sB0->GetNvert()-1))-3.5*
+ sB3->GetDX()*TMath::Cos(t*TMath::DegToRad());
+ y0 = 0.5*(sB0->GetY(0)+sB0->GetY(sB0->GetNvert()-1))-3.5*
+ sB3->GetDX()*TMath::Sin(t*TMath::DegToRad());
+ rotrans = new TGeoCombiTrans("",1.01*x0,y0,z0,rot);
+ vM0->AddNode(vB3,3,rotrans); // Put Mounting bracket on sector
+ rotrans = new TGeoCombiTrans("",1.01*x0,y0,-z0,rot);
+ vM0->AddNode(vB3,4,rotrans); // Put Mounting bracket on sector
+ if(GetDebug(3)){
+ vM0->PrintNodes();
vA0->PrintNodes();
vA1->PrintNodes();
vB0->PrintNodes();
vB1->PrintNodes();
- } // end if GetDebug
- //
+ vB2->PrintNodes();
+ vB3->PrintNodes();
+ vTA0->PrintNodes();
+ vTA1->PrintNodes();
+ vTB0->PrintNodes();
+ vTB1->PrintNodes();
+ } // end if(GetDebug(3))
}
//______________________________________________________________________
-void AliITSv11GeometrySPD::HalfStave(TGeoVolume *moth){
- // Define the detail SPD Half Stave geometry.
+Bool_t AliITSv11GeometrySPD::CFHolePoints(Double_t s,Double_t r1,
+ Double_t r2,Double_t l,Double_t &x,Double_t &y) const
+{
+ //
+ // Step along arck a distancs ds and compute boundry of
+ // two holes (radius r1 and r2) a distance l apart (along
+ // x-axis).
// Inputs:
- // none.
- // Outputs:
- // none.
+ // Double_t s fractional Distance along arcs [0-1]
+ // where 0-> alpha=beta=0, 1-> alpha=90 degrees.
+ // Double_t r1 radius at center circle
+ // Double_t r2 radius of displaced circle
+ // Double_t l Distance displaced circle is displaces (x-axis)
+ // Output:
+ // Double_t x x coordinate along double circle.
+ // Double_t y y coordinate along double circle.
// Return:
- // none.
+ // logical, kFALSE if an error
+ //
+ Double_t alpha,beta;
+ Double_t ac,bc,scb,sca,t,alphac,betac; // at intersection of two circles
- if(moth==0){
- Error("HalfStave","moth=%p",moth);
- return;
- } // end if moth==0
+ x=y=0.0;
+ ac = r1*r1-l*l-r2*r2;
+ bc = 2.*l*r2;
+ if(bc==0.0) {printf("bc=0 l=%e r2=%e\n",l,r2);return kFALSE;}
+ betac = TMath::ACos(ac/bc);
+ alphac = TMath::Sqrt((bc-ac)*(bc+ac))/(2.*l*r1);
+ scb = r2*betac;
+ sca = r1*alphac;
+ t = r1*0.5*TMath::Pi() - sca + scb;
+ if(s<= scb/t){
+ beta = s*t/r2;
+ x = r2*TMath::Cos(beta) + l;
+ y = r2*TMath::Sin(beta);
+ //printf("betac=%e scb=%e t=%e s=%e beta=%e x=%e y=%e\n",
+ // betac,scb,t,s,beta,x,y);
+ return kTRUE;
+ }else{
+ beta = (s*t-scb+sca)/(r1*0.5*TMath::Pi());
+ alpha = beta*0.5*TMath::Pi();
+ x = r1*TMath::Cos(alpha);
+ y = r1*TMath::Sin(alpha);
+ //printf("alphac=%e sca=%e t=%e s=%e beta=%e alpha=%e x=%e y=%e\n",
+ // alphac,sca,t,s,beta,alpha,x,y);
+ return kTRUE;
+ } // end if
+ return kFALSE;
}
-//----------------------------------------------------------------------
-void AliITSv11GeometrySPD::CreateFigure0(const Char_t *filepath,
- const Char_t *type){
- // Creates Figure 0 for the documentation of this class. In this
- // specific case, it creates the X,Y cross section of the SPD suport
- // section, center and ends. The output is written to a standard
- // file name to the path specificed.
- // Inputs:
- // const Char_t *filepath Path where the figure is to be drawn
- // const Char_t *type The type of file, default is gif.
- // Output:
- // none.
- // Return:
- // none.
- TGeoXtru *sA0,*sA1,*sB0,*sB1;
- //TPolyMarker *pmA,*pmB;
- TPolyLine plA0,plA1,plB0,plB1;
- TCanvas *canvas;
- TLatex txt;
- Double_t x,y;
+//______________________________________________________________________
+Bool_t AliITSv11GeometrySPD::GetSectorMountingPoints(Int_t index,Double_t &x0,
+ Double_t &y0, Double_t &x1, Double_t &y1) const
+{
+ //
+ // Returns the edges of the straight borders in the SPD sector shape,
+ // which are used to mount staves on them.
+ // Coordinate system is that of the carbon fiber sector volume.
+ // ---
+ // Index numbering is as follows:
+ // /5
+ // /\/4
+ // 1\ \/3
+ // 0|___\/2
+ // ---
+ // Arguments [the ones passed by reference contain output values]:
+ // Int_t index --> location index according to above scheme [0-5]
+ // Double_t &x0 --> (by ref) x0 location or the ladder sector [cm]
+ // Double_t &y0 --> (by ref) y0 location of the ladder sector [cm]
+ // Double_t &x1 --> (by ref) x1 location or the ladder sector [cm]
+ // Double_t &y1 --> (by ref) y1 location of the ladder sector [cm]
+ // TGeoManager *mgr --> The TGeo builder
+ // ---
+ // The location is described by a line going from (x0, y0) to (x1, y1)
+ // ---
+ // Returns kTRUE if no problems encountered.
+ // Returns kFALSE if a problem was encountered (e.g.: shape not found).
+ //
+ Int_t isize = fSPDsectorX0.GetSize();
- sA0 = (TGeoXtru*) gGeomManager->GetVolume(
- "ITSSPDCarbonFiberSupportSectorA0_1")->GetShape();
- sA1 = (TGeoXtru*) gGeomManager->GetVolume(
- "ITSSPDCarbonFiberSupportSectorAirA1_1")->GetShape();
- sB0 = (TGeoXtru*) gGeomManager->GetVolume(
- "ITSSPDCarbonFiberSupportSectorEndB0_1")->GetShape();
- sB1 = (TGeoXtru*) gGeomManager->GetVolume(
- "ITSSPDCarbonFiberSupportSectorEndAirB1_1")->GetShape();
- //pmA = new TPolyMarker();
- //pmA.SetMarkerStyle(2); // +
- //pmA.SetMarkerColor(7); // light blue
- //pmB = new TPolyMarker();
- //pmB.SetMarkerStyle(5); // X
- //pmB.SetMarkerColor(6); // purple
- plA0.SetPolyline(sA0->GetNvert());
- plA0.SetLineColor(1); // black
- plA0.SetLineStyle(1);
- plA1.SetPolyline(sA1->GetNvert());
- plA1.SetLineColor(2); // red
- plA1.SetLineStyle(1);
- plB0.SetPolyLine(sB0.GetNvert());
- plB0.SetLineColor(3); // Green
- plB0.SetLineStyle(2);
- plB1.SetPolyLine(sB1->GetNvert());
- plB1.SetLineColor(4); // Blue
- plB1.SetLineStyle(2);
- //for(i=0;i<kNRadii;i++) pmA.SetPoint(i,xyB1p[i][0],xyB1p[i][1]);
- //for(i=0;i<kNRadii;i++) pmB.SetPoint(i,xyB1p[i][0],xyB1p[i][1]);
- for(i=0;i<sA0->GetNvert();i++) plA0.SetPoint(i,sA0->GetX(i),sA0->GetY(i));
- for(i=0;i<sA1->GetNvert();i++) plA1.SetPoint(i,sA1->GetX(i),sA1->GetY(i));
- for(i=0;i<sB0->GetNvert();i++) plB0.SetPoint(i,sB0->GetX(i),sB0->GetY(i));
- for(i=0;i<sB1->GetNvert();i++) plB1.SetPoint(i,sB1->GetX(i),sB1->GetY(i));
- canvas = new TCanvas("AliITSv11GeometrySPDFig0","",1000,1000);
- canvas.Range(-3.,-3.,3.,3.);
- txt.SetTextsize(0.05);
- txt.SetTextAlign(33);
- txt.SetTextColor(1);
- txt.Draw(2.9,2.9,"Section A-A outer Carbon Fiber surface");
- txt.SetTextColor(2);
- txt.Draw(2.9,2.5,"Section A-A Inner Carbon Fiber surface");
- txt.SetTextColor(3);
- txt.Draw(2.9,2.1,"Section E-E outer Carbon Fiber surface");
- txt.SetTextColor(4);
- txt.Draw(2.9,1.7,"Section E-E Inner Carbon Fiber surface");
- plA0.Draw();
- plA1.Draw();
- plB0.Draw();
- plB1.Draw();
- //pmA.Draw();
- //pmB.Draw();
+ x0 = x1 = y0 = y1 = 0.0;
+ if(index < 0 || index > isize) {
+ AliError(Form("index = %d: allowed 0 --> %", index, isize));
+ return kFALSE;
+ } // end if(index<0||index>isize)
+ x0 = fSPDsectorX0[index];
+ x1 = fSPDsectorX1[index];
+ y0 = fSPDsectorY0[index];
+ y1 = fSPDsectorY1[index];
+ return kTRUE;
+}
+//______________________________________________________________________
+void AliITSv11GeometrySPD::SPDsectorShape(Int_t n,const Double_t *xc,
+ const Double_t *yc, const Double_t *r,
+ const Double_t *ths, const Double_t *the,
+ Int_t npr, Int_t &m, Double_t **xp, Double_t **yp) const
+{
//
- Char_t chr[3];
- for(i=0;i<kNRadii;i++){
- sprintf(chr,"%2d",i);txt.DrawLatex(x-0.1,y,chr);
- sprintf(chr,"%8.4",);txt.DrawLatex(x,y,chr);
- sprintf(chr,"%8.4",);txt.DrawLatex(x+0.5,y,chr);
- sprintf(chr,"%8.4",);txt.DrawLatex(x+1.0,y,chr);
- sprintf(chr,"%8.4",);txt.DrawLatex(x+1.5,y,chr);
- sprintf(chr,"%8.4",);txt.DrawLatex(x+2.0,y,chr);
- if() txt.DrawLatex(x+2.5,y,"A-A/E-E");
- else txt.DrawLatex(x+2.5,y,"E-E");
- } // end for i
- txt.DrawLatex(x,y,"x_{c} mm");
- txt.DrawLatex(x+0.5,y,"y_{c} mm");
- txt.DrawLatex(x+1.0,y,"R mm");
- txt.DrawLatex(x+1.5,y,"#theta_{start}^{#circle}");
- txt.DrawLatex(x+2.0,y,"#theta_{end}^{#circle}");
- txt.DrawLatex(x+2.5,y,"Section");
+ // Code to compute the points that make up the shape of the SPD
+ // Carbon fiber support sections
+ // Inputs:
+ // Int_t n size of arrays xc,yc, and r.
+ // Double_t *xc array of x values for radii centers.
+ // Double_t *yc array of y values for radii centers.
+ // Double_t *r array of signed radii values.
+ // Double_t *ths array of starting angles [degrees].
+ // Double_t *the array of ending angles [degrees].
+ // Int_t npr the number of lines segments to aproximate the arc.
+ // Outputs (arguments passed by reference):
+ // Int_t m the number of enetries in the arrays *xp[npr+1]
+ // and *yp[npr+1].
+ // Double_t **xp array of x coordinate values of the line segments
+ // which make up the SPD support sector shape.
+ // Double_t **yp array of y coordinate values of the line segments
+ // which make up the SPD support sector shape.
//
+ Int_t i, k;
+ Double_t t, t0, t1;
+
+ m = n*(npr + 1);
+ if(GetDebug(2)) {
+ cout <<" X \t Y \t R \t S \t E" << m << endl;
+ for(i = 0; i < n; i++) {
+ cout << "{" << xc[i] << ", ";
+ cout << yc[i] << ", ";
+ cout << r[i] << ", ";
+ cout << ths[i] << ", ";
+ cout << the[i] << "}, " << endl;
+ } // end for i
+ } // end if(GetDebug(2))
+ if (GetDebug(3)) cout << "Double_t sA0 = [" << n*(npr+1)+1<<"][";
+ if (GetDebug(4)) cout << "3] {";
+ else if(GetDebug(3)) cout <<"2] {";
+ t0 = (Double_t)npr;
+ for(i = 0; i < n; i++) {
+ t1 = (the[i] - ths[i]) / t0;
+ if(GetDebug(5)) cout << "t1 = " << t1 << endl;
+ for(k = 0; k <= npr; k++) {
+ t = ths[i] + ((Double_t)k) * t1;
+ xp[i][k] = TMath::Abs(r[i]) * CosD(t) + xc[i];
+ yp[i][k] = TMath::Abs(r[i]) * SinD(t) + yc[i];
+ if(GetDebug(3)) {
+ cout << "{" << xp[i][k] << "," << yp[i][k];
+ if (GetDebug(4)) cout << "," << t;
+ cout << "},";
+ } // end if GetDebug
+ } // end for k
+ if(GetDebug(3)) cout << endl;
+ } // end of i
+ if(GetDebug(3)) cout << "{" << xp[0][0] << ", " << yp[0][0];
+ if(GetDebug(4)) cout << "," << ths[0];
+ if(GetDebug(3)) cout << "}}" << endl;
+}
+
+//______________________________________________________________________
+TGeoVolume* AliITSv11GeometrySPD::CreateLadder(Int_t layer,TArrayD &sizes,
+ TGeoManager *mgr) const
+{
+ //
+ // Creates the "ladder" = silicon sensor + 5 chips.
+ // Returns a TGeoVolume containing the following components:
+ // - the sensor (TGeoBBox), whose name depends on the layer
+ // - 5 identical chips (TGeoBBox)
+ // - a guard ring around the sensor (subtraction of TGeoBBoxes),
+ // which is separated from the rest of sensor because it is not
+ // a sensitive part
+ // - bump bondings (TGeoBBox stripes for the whole width of the
+ // sensor, one per column).
+ // ---
+ // Arguments:
+ // 1 - the owner layer (MUST be 1 or 2 or a fatal error is raised)
+ // 2 - a TArrayD passed by reference, which will contain relevant
+ // dimensions related to this object:
+ // size[0] = 'thickness' (the smallest dimension)
+ // size[1] = 'length' (the direction along the ALICE Z axis)
+ // size[2] = 'width' (extension in the direction perp. to the
+ // above ones)
+ // 3 - the used TGeoManager
+
+ // ** CRITICAL CHECK **
+ // layer number can be ONLY 1 or 2
+ if (layer != 1 && layer != 2) AliFatal("Layer number MUST be 1 or 2");
+
+ // ** MEDIA **
+ TGeoMedium *medAir = GetMedium("AIR$",mgr);
+ TGeoMedium *medSPDSiChip = GetMedium("SPD SI CHIP$",mgr); // SPD SI CHIP
+ TGeoMedium *medSi = GetMedium("SI$",mgr);
+ TGeoMedium *medBumpBond = GetMedium("COPPER$",mgr); // ??? BumpBond
+
+ // ** SIZES **
+ Double_t chipThickness = fgkmm * 0.150;
+ Double_t chipWidth = fgkmm * 15.950;
+ Double_t chipLength = fgkmm * 13.600;
+ Double_t chipSpacing = fgkmm * 0.400; // separation of chips along Z
+ Double_t sensThickness = fgkmm * 0.200;
+ Double_t sensLength = fgkmm * 69.600;
+ Double_t sensWidth = fgkmm * 12.800;
+ Double_t guardRingWidth = fgkmm * 0.560; // a border of this thickness
+ // all around the sensor
+ Double_t bbLength = fgkmm * 0.042;
+ Double_t bbWidth = sensWidth;
+ Double_t bbThickness = fgkmm * 0.012;
+ Double_t bbPos = 0.080; // Z position w.r. to left pixel edge
+ // compute the size of the container volume which
+ // will also be returned in the referenced TArrayD;
+ // for readability, they are linked by reference to a more meaningful name
+ sizes.Set(3);
+ Double_t &thickness = sizes[0];
+ Double_t &length = sizes[1];
+ Double_t &width = sizes[2];
+ // the container is a box which exactly enclose all the stuff;
+ width = chipWidth;
+ length = sensLength + 2.0*guardRingWidth;
+ thickness = sensThickness + chipThickness + bbThickness;
+
+ // ** VOLUMES **
+ // While creating this volume, since it is a sensitive volume,
+ // we must respect some standard criteria for its local reference frame.
+ // Local X must correspond to x coordinate of the sensitive volume:
+ // this means that we are going to create the container with a local
+ // reference system that is **not** in the middle of the box.
+ // This is accomplished by calling the shape constructor with an
+ // additional option ('originShift'):
+ Double_t xSens = 0.5 * (width - sensWidth - 2.0*guardRingWidth);
+ Double_t originShift[3] = {-xSens, 0., 0.};
+ TGeoBBox *shapeContainer = new TGeoBBox(0.5*width,0.5*thickness,
+ 0.5*length,originShift);
+ // then the volume is made of air, and using this shape
+ TGeoVolume *container = new TGeoVolume(Form("ITSSPDlay%d-Ladder",layer),
+ shapeContainer, medAir);
+ // the chip is a common box
+ TGeoVolume *volChip = mgr->MakeBox("ITSSPDchip",medSPDSiChip,
+ 0.5*chipWidth,0.5*chipThickness,0.5*chipLength);
+ // the sensor as well
+ TGeoVolume *volSens = mgr->MakeBox(GetSenstiveVolumeName(layer),medSi,
+ 0.5*sensWidth,0.5*sensThickness,0.5*sensLength);
+ // the guard ring shape is the subtraction of two boxes with the
+ // same center.
+ TGeoBBox *shIn = new TGeoBBox(0.5*sensWidth,sensThickness,0.5*sensLength);
+ TGeoBBox *shOut = new TGeoBBox(0.5*sensWidth+guardRingWidth,
+ 0.5*sensThickness,0.5*sensLength+guardRingWidth);
+ shIn->SetName("ITSSPDinnerBox");
+ shOut->SetName("ITSSPDouterBox");
+ TGeoCompositeShape *shBorder = new TGeoCompositeShape(
+ "ITSSPDgaurdRingBorder",Form("%s-%s",shOut->GetName(),shIn->GetName()));
+ TGeoVolume *volBorder = new TGeoVolume("ITSSPDgaurdRing",shBorder,medSi);
+ // bump bonds for one whole column
+ TGeoVolume *volBB = mgr->MakeBox("ITSSPDbb",medBumpBond,0.5*bbWidth,
+ 0.5*bbThickness,0.5*bbLength);
+ // set colors of all objects for visualization
+ volSens->SetLineColor(kYellow + 1);
+ volChip->SetLineColor(kGreen);
+ volBorder->SetLineColor(kYellow + 3);
+ volBB->SetLineColor(kGray);
+
+ // ** MOVEMENTS **
+ // sensor is translated along thickness (X) and width (Y)
+ Double_t ySens = 0.5 * (thickness - sensThickness);
+ Double_t zSens = 0.0;
+ // we want that the x of the ladder is the same as the one of
+ // its sensitive volume
+ TGeoTranslation *trSens = new TGeoTranslation(0.0, ySens, zSens);
+ // bump bonds are translated along all axes:
+ // keep same Y used for sensors, but change the Z
+ TGeoTranslation *trBB[160];
+ Double_t x = 0.0;
+ Double_t y = 0.5 * (thickness - bbThickness) - sensThickness;
+ Double_t z = -0.5 * sensLength + guardRingWidth + fgkmm*0.425 - bbPos;
+ Int_t i;
+ for (i = 0; i < 160; i++) {
+ trBB[i] = new TGeoTranslation(x, y, z);
+ switch(i) {
+ case 31:case 63:case 95:case 127:
+ z += fgkmm * 0.625 + fgkmm * 0.2;
+ break;
+ default:
+ z += fgkmm * 0.425;
+ } // end switch
+ } // end for i
+ // the chips are translated along the length (Z) and thickness (X)
+ TGeoTranslation *trChip[5] = {0, 0, 0, 0, 0};
+ x = -xSens;
+ y = 0.5 * (chipThickness - thickness);
+ z = 0.0;
+ for (i = 0; i < 5; i++) {
+ z = -0.5*length + guardRingWidth
+ + (Double_t)i*chipSpacing + ((Double_t)(i) + 0.5)*chipLength;
+ trChip[i] = new TGeoTranslation(x, y, z);
+ } // end ofr i
+
+ // add nodes to container
+ container->AddNode(volSens, 1, trSens);
+ container->AddNode(volBorder, 1, trSens);
+ for (i = 0; i < 160; i++) container->AddNode(volBB,i+1,trBB[i]);
+ for (i = 0; i < 5; i++) container->AddNode(volChip,i+3,trChip[i]);
+ // return the container
+ return container;
+}
+
+/*
+//______________________________________________________________________
+TGeoVolume* AliITSv11GeometrySPD::CreateLadder
+ (Int_t layer, TArrayD &sizes, TGeoManager *mgr) const
+{
+ //
+ // Creates the "ladder" = silicon sensor + 5 chips.
+ // Returns a TGeoVolume containing the following components:
+ // - the sensor (TGeoBBox), whose name depends on the layer
+ // - 5 identical chips (TGeoBBox)
+ // - a guard ring around the sensor (subtraction of TGeoBBoxes),
+ // which is separated from the rest of sensor because it is not
+ // a sensitive part
+ // - bump bondings (TGeoBBox stripes for the whole width of the
+ // sensor, one per column).
+ // ---
+ // Arguments:
+ // 1 - the owner layer (MUST be 1 or 2 or a fatal error is raised)
+ // 2 - a TArrayD passed by reference, which will contain relevant
+ // dimensions related to this object:
+ // size[0] = 'thickness' (the smallest dimension)
+ // size[1] = 'length' (the direction along the ALICE Z axis)
+ // size[2] = 'width' (extension in the direction perp. to the
+ // above ones)
+ // 3 - the used TGeoManager
+
+ // ** CRITICAL CHECK ******************************************************
+ // layer number can be ONLY 1 or 2
+ if (layer != 1 && layer != 2) AliFatal("Layer number MUST be 1 or 2");
+
+ // ** MEDIA ***************************************************************
+
+ TGeoMedium *medAir = GetMedium("AIR$",mgr);
+ TGeoMedium *medSPDSiChip = GetMedium("SPD SI CHIP$",mgr); // SPD SI CHIP
+ TGeoMedium *medSi = GetMedium("SI$",mgr);
+ TGeoMedium *medBumpBond = GetMedium("COPPER$",mgr); // ??? BumpBond
+
+ // ** SIZES ***************************************************************
+
+ Double_t chipThickness = fgkmm * 0.150;
+ Double_t chipWidth = fgkmm * 15.950;
+ Double_t chipLength = fgkmm * 13.600;
+ Double_t chipSpacing = fgkmm * 0.400; // separation of chips along Z
+ Double_t sensThickness = fgkmm * 0.200;
+ Double_t sensLength = fgkmm * 69.600;
+ Double_t sensWidth = fgkmm * 12.800;
+ Double_t guardRingWidth = fgkmm * 0.560; // guard ring around sensor
+ Double_t bbLength = fgkmm * 0.042;
+ Double_t bbWidth = sensWidth;
+ Double_t bbThickness = fgkmm * 0.012;
+ Double_t bbPos = 0.080; // Z position w.r. to left pixel edge
+
+ // the three dimensions of the box which contains the ladder
+ // are returned in the 'sizes' argument, and are used for volumes positionement
+ // for readability purpose, they are linked by reference to a more meaningful name
+ sizes.Set(3);
+ Double_t &thickness = sizes[0];
+ Double_t &length = sizes[1];
+ Double_t &width = sizes[2];
+ // the container is a box which exactly enclose all the stuff
+ width = chipWidth;
+ length = sensLength + 2.0*guardRingWidth;
+ thickness = sensThickness + chipThickness + bbThickness;
+
+ // ** VOLUMES *************************************************************
+
+ // This is a sensitive volume.
+ // Local X must correspond to x coordinate of the sensitive volume:
+ // to respect this, the origin of the local reference system
+ // must be shifted from the middle of the box, using
+ // an additional option ('originShift') when creating the container shape:
+ Double_t xSens = 0.5 * (width - sensWidth - 2.0*guardRingWidth);
+ Double_t originShift[3] = {-xSens, 0., 0.};
+
+ // now the container is a TGeoBBox with this shift,
+ // and the volume is made of air (it does not exist in reality)
+ TGeoBBox *shLadder = new TGeoBBox(0.5*width, 0.5*thickness, 0.5*length, originShift);
+ TGeoVolume *vLadder = new TGeoVolume(Form("ITSSPDlay%d-Ladder", layer), shLadder, medAir);
+
+ // the chip is a common box
+ TGeoVolume *vChip = mgr->MakeBox("ITSSPDchip", medSPDSiChip,
+ 0.5*chipWidth, 0.5*chipThickness, 0.5*chipLength);
+
+ // to build the sensor with its guard ring, we create a TGeoBBox with the size
+ // of the sensor + guard ring, and we insert the true sensor into it as an
+ // internal node: this simplifies the implementation with the same result
+ TGeoVolume *vSensGuard = mgr->MakeBox(Form("%s-guardRing", GetSenstiveVolumeName(layer)),
+ medSi,
+ 0.5*sensWidth + guardRingWidth,
+ 0.5*sensThickness,
+ 0.5*sensLength + guardRingWidth);
+ TGeoVolume *vSens = mgr->MakeBox(GetSenstiveVolumeName(layer), medSi,
+ 0.5*sensWidth,0.5*sensThickness,0.5*sensLength);
+ vSensGuard->AddNode(vSens, 0);
+ vSensGuard->SetTransparency(50);
+
+ // bump bond is a common box for one whole column
+ TGeoVolume *vBB = mgr->MakeBox("ITSSPDbb", medBumpBond,
+ 0.5*bbWidth, 0.5*bbThickness, 0.5*bbLength);
+
+ // set colors of all objects for visualization
+ vLadder->SetLineColor(kRed);
+ vSens->SetLineColor(kYellow + 1);
+ vChip->SetLineColor(kGreen);
+ vSensGuard->SetLineColor(kYellow + 3);
+ vBB->SetLineColor(kGray);
+
+ // ** MOVEMENTS **
+ // sensor is translated along thickness (Y) and width (X)
+ Double_t ySens = 0.5 * (thickness - sensThickness);
+ Double_t zSens = 0.0;
+ // we want that the x of the ladder is the same as the one of
+ // its sensitive volume
+ TGeoTranslation *trSens = new TGeoTranslation(0.0, ySens, zSens);
+ // bump bonds are translated along all axes:
+ // keep same Y used for sensors, but change the Z
+ TGeoTranslation *trBB[160];
+ Double_t x = 0.0;
+ Double_t y = 0.5 * (thickness - bbThickness) - sensThickness;
+ Double_t z = -0.5 * sensLength + guardRingWidth + fgkmm*0.425 - bbPos;
+ Int_t i;
+ for (i = 0; i < 160; i++) {
+ trBB[i] = new TGeoTranslation(x, y, z);
+ switch(i) {
+ case 31:case 63:case 95:case 127:
+ z += fgkmm * 0.625 + fgkmm * 0.2;
+ break;
+ default:
+ z += fgkmm * 0.425;
+ } // end switch
+ } // end for i
+ // the chips are translated along the length (Z) and thickness (X)
+ TGeoTranslation *trChip[5] = {0, 0, 0, 0, 0};
+ x = -xSens;
+ y = 0.5 * (chipThickness - thickness);
+ z = 0.0;
+ for (i = 0; i < 5; i++) {
+ z = -0.5*length + guardRingWidth
+ + (Double_t)i*chipSpacing + ((Double_t)(i) + 0.5)*chipLength;
+ trChip[i] = new TGeoTranslation(x, y, z);
+ } // end ofr i
+
+ // add nodes to container
+ vLadder->AddNode(vSensGuard, 1, trSens);
+ //vLadderAddNode(volBorder, 1, trSens);
+ for (i = 0; i < 160; i++) vLadder->AddNode(vBB,i+1,trBB[i]);
+ for (i = 0; i < 5; i++) vLadder->AddNode(vChip,i+3,trChip[i]);
+ // return the container
+ return vLadder;
+}
+*/
+
+//______________________________________________________________________
+TGeoVolume* AliITSv11GeometrySPD::CreateClip(TArrayD &sizes,Bool_t isDummy,
+ TGeoManager *mgr) const
+{
+ //
+ // Creates the carbon fiber clips which are added to the central ladders.
+ // They have a complicated shape which is approximated by a TGeoXtru
+ // Implementation of a single clip over an half-stave.
+ // It has a complicated shape which is approximated to a section like this:
+ //
+ // 6
+ // /\ .
+ // 7 //\\ 5
+ // / 1\\___________________4
+ // 0 \___________________
+ // 2 3
+ // with a finite thickness for all the shape
+ // Its local reference frame is such that point A corresponds to origin.
+ //
+ Double_t fullLength = fgkmm * 12.6; // = x4 - x0
+ Double_t flatLength = fgkmm * 5.4; // = x4 - x3
+ Double_t inclLongLength = fgkmm * 5.0; // = 5-6
+ Double_t inclShortLength = fgkmm * 2.0; // = 6-7
+ Double_t fullHeight = fgkmm * 2.8; // = y6 - y3
+ Double_t thickness = fgkmm * 0.18; // thickness
+ Double_t totalLength = fgkmm * 52.0; // total length in Z
+ Double_t holeSize = fgkmm * 5.0; // dimension of cubic
+ // hole inserted for pt1000
+ Double_t angle1 = 27.0; // supplementary of angle DCB
+ Double_t angle2; // angle DCB
+ Double_t angle3; // angle of GH with vertical
+
+ angle2 = 0.5 * (180.0 - angle1);
+ angle3 = 90.0 - TMath::ACos(fullLength - flatLength -
+ inclLongLength*TMath::Cos(angle1)) *
+ TMath::RadToDeg();
+ angle1 *= TMath::DegToRad();
+ angle2 *= TMath::DegToRad();
+ angle3 *= TMath::DegToRad();
+
+ Double_t x[8], y[8];
+
+ x[0] = 0.0;
+ x[1] = x[0] + fullLength - flatLength - inclLongLength*TMath::Cos(angle1);
+ x[2] = x[0] + fullLength - flatLength;
+ x[3] = x[0] + fullLength;
+ x[4] = x[3];
+ x[5] = x[4] - flatLength + thickness * TMath::Cos(angle2);
+ x[6] = x[1];
+ x[7] = x[0];
+
+ y[0] = 0.0;
+ y[1] = y[0] + inclShortLength * TMath::Cos(angle3);
+ y[2] = y[1] - inclLongLength * TMath::Sin(angle1);
+ y[3] = y[2];
+ y[4] = y[3] + thickness;
+ y[5] = y[4];
+ y[6] = y[1] + thickness;
+ y[7] = y[0] + thickness;
+
+ sizes.Set(7);
+ sizes[0] = totalLength;
+ sizes[1] = fullHeight;
+ sizes[2] = y[2];
+ sizes[3] = y[6];
+ sizes[4] = x[0];
+ sizes[5] = x[3];
+ sizes[6] = x[2];
+
+ if(isDummy){// use this argument when on ewant just the
+ // positions without create any volume
+ return NULL;
+ } // end if isDummy
+
+ TGeoXtru *shClip = new TGeoXtru(2);
+ shClip->SetName("ITSSPDshclip");
+ shClip->DefinePolygon(8, x, y);
+ shClip->DefineSection(0, -0.5*totalLength, 0., 0., 1.0);
+ shClip->DefineSection(1, 0.5*totalLength, 0., 0., 1.0);
+
+ TGeoBBox *shHole = new TGeoBBox("ITSSPDSHClipHole",0.5*holeSize,
+ 0.5*holeSize,0.5*holeSize);
+ TGeoTranslation *tr1 = new TGeoTranslation("ITSSPDTRClipHole1",x[2],0.0,
+ fgkmm*14.);
+ TGeoTranslation *tr2 = new TGeoTranslation("ITSSPDTRClipHole2",x[2],0.0,
+ 0.0);
+ TGeoTranslation *tr3 = new TGeoTranslation("ITSSPDTRClipHole3",x[2],0.0,
+ -fgkmm*14.);
+ tr1->RegisterYourself();
+ tr2->RegisterYourself();
+ tr3->RegisterYourself();
+
+ //TString strExpr("ITSSPDshclip-(");
+ TString strExpr(shClip->GetName());
+ strExpr.Append("-(");
+ strExpr.Append(Form("%s:%s+", shHole->GetName(), tr1->GetName()));
+ strExpr.Append(Form("%s:%s+", shHole->GetName(), tr2->GetName()));
+ strExpr.Append(Form("%s:%s)", shHole->GetName(), tr3->GetName()));
+ TGeoCompositeShape *shClipHole = new TGeoCompositeShape(
+ "ITSSPDSHClipHoles",strExpr.Data());
+
+ TGeoMedium *mat = GetMedium("SPD C (M55J)$", mgr);
+ TGeoVolume *vClip = new TGeoVolume("ITSSPDclip", shClipHole, mat);
+ vClip->SetLineColor(kGray + 2);
+ return vClip;
+}//______________________________________________________________________
+TGeoCompositeShape* AliITSv11GeometrySPD::CreateGroundingFoilShape
+ (Int_t itype,Double_t &length,Double_t &width,
+ Double_t thickness,TArrayD &sizes)
+{
+ //
+ // Creates the typical composite shape of the grounding foil:
+ //
+ // +---------------------------------------------------------+
+ // | 5 6 9 |
+ // | +-----------+ +------------+ 10
+ // | O | | |
+ // | 3 /-----+ 4 +------+
+ // | 1 / 7 8
+ // | /----------/
+ // +-----/ 2 +
+ // 0
+ // Z + 11
+ //
+ // This shape is used 4 times: two layers of glue, one in kapton
+ // and one in aluminum, taking into account that the aliminum
+ // layer has small differences in the size of some parts.
+ // ---
+ // In order to overcome problems apparently due to a large number
+ // of points, the shape creation is done according the following
+ // steps:
+ // 1) a TGeoBBox is created with a size right enough to contain
+ // the whole shape (0-1-X-13)
+ // 2) holes are defined as other TGeoBBox which are subtracted
+ // from the main shape
+ // 3) a TGeoXtru is defined connecting the points (0-->11-->0)
+ // and is also subtracted from the main shape
+ // ---
+ // The argument ("type") is used to choose between all these
+ // possibilities:
+ // - type = 0 --> kapton layer
+ // - type = 1 --> aluminum layer
+ // - type = 2 --> glue layer between support and GF
+ // - type = 3 --> glue layer between GF and ladders
+ // Returns: a TGeoCompositeShape which will then be used to shape
+ // several volumes. Since TGeoXtru is used, the local reference
+ // frame of this object has X horizontal and Y vertical w.r to
+ // the shape drawn above, and Z axis going perpendicularly to the screen.
+ // This is not the correct reference for the half stave, for which
+ // the "long" dimension is Z and the "short" is X, while Y goes in
+ // the direction of thickness. This will imply some rotations when
+ // using the volumes created with this shape.
+
+ // suffix to differentiate names
+ Char_t type[10];
+
+ // size of the virtual box containing exactly this volume
+ length = fgkmm * 243.18;
+ width = fgkmm * 15.95;
+ if (itype == 1) {
+ length -= fgkmm * 0.4;
+ width -= fgkmm * 0.4;
+ } // end if itype==1
+ switch (itype) {
+ case 0:
+ sprintf(type,"Kap");
+ break;
+ case 1:
+ sprintf(type,"Alu");
+ break;
+ case 2:
+ sprintf(type,"Glue1");
+ break;
+ case 3:
+ sprintf(type,"Glue2");
+ break;
+ }
+ // we divide the shape in several slices along the horizontal
+ // direction (local X) here we define define the length of all
+ // sectors (from leftmost to rightmost)
+ Int_t i;
+ Double_t sliceLength[] = { 140.71, 2.48, 26.78, 4.00,
+ 10.00, 24.40, 10.00, 24.81 };
+ for (i = 0; i < 8; i++) sliceLength[i] *= fgkmm;
+ if (itype == 1) {
+ sliceLength[0] -= fgkmm * 0.2;
+ sliceLength[4] -= fgkmm * 0.2;
+ sliceLength[5] += fgkmm * 0.4;
+ sliceLength[6] -= fgkmm * 0.4;
+ } // end if itype ==1
+
+ // as shown in the drawing, we have four different widths
+ // (along local Y) in this shape:
+ Double_t widthMax = fgkmm * 15.95;
+ Double_t widthMed1 = fgkmm * 15.00;
+ Double_t widthMed2 = fgkmm * 11.00;
+ Double_t widthMin = fgkmm * 4.40;
+ if (itype == 1) {
+ widthMax -= fgkmm * 0.4;
+ widthMed1 -= fgkmm * 0.4;
+ widthMed2 -= fgkmm * 0.4;
+ widthMin -= fgkmm * 0.4;
+ } // end if itype==1
+
+ // create the main shape
+ TGeoBBox *shGroundFull = 0;
+ shGroundFull = new TGeoBBox(Form("ITSSPDSHgFoil%sFull", type),
+ 0.5*length,0.5*width, 0.5*thickness);
+
+ // create the polygonal shape to be subtracted to give the correct
+ // shape to the borders its vertices are defined in sugh a way that
+ // this polygonal will be placed in the correct place considered
+ // that the origin of the local reference frame is in the center
+ // of the main box: we fix the starting point at the lower-left
+ // edge of the shape (point 12), and add all points in order,
+ // following a clockwise rotation
+
+ Double_t x[13], y[13];
+ x[ 0] = -0.5 * length + sliceLength[0];
+ y[ 0] = -0.5 * widthMax;
+
+ x[ 1] = x[0] + sliceLength[1];
+ y[ 1] = y[0] + (widthMax - widthMed1);
+
+ x[ 2] = x[1] + sliceLength[2];
+ y[ 2] = y[1];
+
+ x[ 3] = x[2] + sliceLength[3];
+ y[ 3] = y[2] + (widthMed1 - widthMed2);
+
+ x[ 4] = x[3] + sliceLength[4];
+ y[ 4] = y[3];
+
+ x[ 5] = x[4];
+ y[ 5] = y[4] + (widthMed2 - widthMin);
+
+ x[ 6] = x[5] + sliceLength[5];
+ y[ 6] = y[5];
+
+ x[ 7] = x[6];
+ y[ 7] = y[4];
+
+ x[ 8] = x[7] + sliceLength[6];
+ y[ 8] = y[7];
+
+ x[ 9] = x[8];
+ y[ 9] = y[6];
+
+ x[10] = x[9] + sliceLength[7] + 0.5;
+ y[10] = y[9];
+
+ x[11] = x[10];
+ y[11] = y[0] - 0.5;
+
+ x[12] = x[0];
+ y[12] = y[11];
+
+ // create the shape
+ TGeoXtru *shGroundXtru = new TGeoXtru(2);
+ shGroundXtru->SetName(Form("ITSSPDSHgFoil%sXtru", type));
+ shGroundXtru->DefinePolygon(13, x, y);
+ shGroundXtru->DefineSection(0, -thickness, 0., 0., 1.0);
+ shGroundXtru->DefineSection(1, thickness, 0., 0., 1.0);
+
+ // define a string which will express the algebric operations among volumes
+ // and add the subtraction of this shape from the main one
+ TString strComposite(Form("ITSSPDSHgFoil%sFull-(%s+", type,
+ shGroundXtru->GetName()));
+
+ // define the holes according to size information coming from drawings:
+ Double_t holeLength = fgkmm * 10.00;
+ Double_t holeWidth = fgkmm * 7.50;
+ Double_t holeSepX0 = fgkmm * 7.05; // separation between center
+ // of first hole and left border
+ Double_t holeSepXC = fgkmm * 14.00; // separation between the centers
+ // of two consecutive holes
+ Double_t holeSepX1 = fgkmm * 15.42; // separation between centers of
+ // 5th and 6th hole
+ Double_t holeSepX2 = fgkmm * 22.00; // separation between centers of
+ // 10th and 11th hole
+ if (itype == 1) {
+ holeSepX0 -= fgkmm * 0.2;
+ holeLength += fgkmm * 0.4;
+ holeWidth += fgkmm * 0.4;
+ } // end if itype==1
+ sizes.Set(7);
+ sizes[0] = holeLength;
+ sizes[1] = holeWidth;
+ sizes[2] = holeSepX0;
+ sizes[3] = holeSepXC;
+ sizes[4] = holeSepX1;
+ sizes[5] = holeSepX2;
+ sizes[6] = fgkmm * 4.40;
+
+ // X position of hole center (will change for each hole)
+ Double_t holeX = -0.5*length;
+ // Y position of center of all holes (= 4.4 mm from upper border)
+ Double_t holeY = 0.5*(width - holeWidth) - widthMin;
+
+ // create a shape for the holes (common)
+ TGeoBBox *shHole = 0;
+ shHole = new TGeoBBox(Form("ITSSPD%sGfoilHole", type),0.5*holeLength,
+ 0.5*holeWidth, thickness);
+
+ // insert the holes in the XTRU shape:
+ // starting from the first value of X, they are simply
+ // shifted along this axis
+ char name[200];
+ TGeoTranslation *transHole[11];
+ for (i = 0; i < 11; i++) {
+ // set the position of the hole, depending on index
+ if (i == 0) {
+ holeX += holeSepX0;
+ }else if (i < 5) {
+ holeX += holeSepXC;
+ }else if (i == 5) {
+ holeX += holeSepX1;
+ }else if (i < 10) {
+ holeX += holeSepXC;
+ }else {
+ holeX += holeSepX2;
+ } // end if else if's
+ //cout << i << " --> X = " << holeX << endl;
+ sprintf(name,"ITSSPDTRgFoil%sHole%d", type, i);
+ transHole[i] = new TGeoTranslation(name, holeX, holeY, 0.0);
+ transHole[i]->RegisterYourself();
+ strComposite.Append(Form("ITSSPD%sGfoilHole:%s", type, name));
+ if (i < 10) strComposite.Append("+"); else strComposite.Append(")");
+ } // end for i
+
+ // create composite shape
+ TGeoCompositeShape *shGround = new TGeoCompositeShape(
+ Form("ITSSPDSHgFoil%s", type), strComposite.Data());
+
+ return shGround;
+}
+//______________________________________________________________________
+TGeoVolumeAssembly* AliITSv11GeometrySPD::CreateGroundingFoil(Bool_t isRight,
+ TArrayD &sizes, TGeoManager *mgr)
+{
+ //
+ // Create a volume containing all parts of the grounding foil a
+ // for a half-stave.
+ // It consists of 4 layers with the same shape but different thickness:
+ // 1) a layer of glue
+ // 2) the aluminum layer
+ // 3) the kapton layer
+ // 4) another layer of glue
+ // ---
+ // Arguments:
+ // 1: a boolean value to know if it is the grounding foir for
+ // the right or left side
+ // 2: a TArrayD which will contain the dimension of the container box:
+ // - size[0] = length along Z (the beam line direction)
+ // - size[1] = the 'width' of the stave, which defines, together
+ // with Z, the plane of the carbon fiber support
+ // - size[2] = 'thickness' (= the direction along which all
+ // stave components are superimposed)
+ // 3: the TGeoManager
+ // ---
+ // The return value is a TGeoBBox volume containing all grounding
+ // foil components.
+ // to avoid strange behaviour of the geometry manager,
+ // create a suffix to be used in the names of all shapes
+ //
+ char suf[5];
+ if (isRight) strcpy(suf, "R"); else strcpy(suf, "L");
+ // this volume will be created in order to ease its placement in
+ // the half-stave; then, it is added here the small distance of
+ // the "central" edge of each volume from the Z=0 plane in the stave
+ // reference (which coincides with ALICE one)
+ Double_t dist = fgkmm * 0.71;
+
+ // define materials
+ TGeoMedium *medKap = GetMedium("SPD KAPTON(POLYCH2)$", mgr);
+ TGeoMedium *medAlu = GetMedium("AL$", mgr);
+ TGeoMedium *medGlue = GetMedium("EPOXY$", mgr); //??? GLUE_GF_SUPPORT
+
+ // compute the volume shapes (thicknesses change from one to the other)
+ Double_t kpLength, kpWidth, alLength, alWidth;
+ TArrayD kpSize, alSize, glSize;
+ Double_t kpThickness = fgkmm * 0.04;
+ Double_t alThickness = fgkmm * 0.01;
+//cout << "AL THICKNESS" << alThickness << endl;
+ //Double_t g0Thickness = fgkmm * 0.1175 - fgkGapHalfStave;
+ //Double_t g1Thickness = fgkmm * 0.1175 - fgkGapLadder;
+ Double_t g0Thickness = fgkmm * 0.1275 - fgkGapHalfStave;
+ Double_t g1Thickness = fgkmm * 0.1275 - fgkGapLadder;
+ TGeoCompositeShape *kpShape = CreateGroundingFoilShape(0,kpLength,kpWidth,
+ kpThickness, kpSize);
+ TGeoCompositeShape *alShape = CreateGroundingFoilShape(1,alLength,alWidth,
+ alThickness, alSize);
+ TGeoCompositeShape *g0Shape = CreateGroundingFoilShape(2,kpLength,kpWidth,
+ g0Thickness, glSize);
+ TGeoCompositeShape *g1Shape = CreateGroundingFoilShape(3,kpLength,kpWidth,
+ g1Thickness, glSize);
+ // create the component volumes and register their sizes in the
+ // passed arrays for readability reasons, some reference variables
+ // explicit the meaning of the array slots
+ TGeoVolume *kpVol = new TGeoVolume(Form("ITSSPDgFoilKap%s",suf),
+ kpShape, medKap);
+ TGeoVolume *alVol = new TGeoVolume(Form("ITSSPDgFoilAlu%s",suf),
+ alShape, medAlu);
+ TGeoVolume *g0Vol = new TGeoVolume(Form("ITSSPDgFoilGlue%s",suf),
+ g0Shape, medGlue);
+ TGeoVolume *g1Vol = new TGeoVolume(Form("ITSSPDgFoilGlue%s",suf),
+ g1Shape, medGlue);
+ // set colors for the volumes
+ kpVol->SetLineColor(kRed);
+ alVol->SetLineColor(kGray);
+ g0Vol->SetLineColor(kYellow);
+ g1Vol->SetLineColor(kYellow);
+ // create references for the final size object
+ if (sizes.GetSize() != 3) sizes.Set(3);
+ Double_t &fullThickness = sizes[0];
+ Double_t &fullLength = sizes[1];
+ Double_t &fullWidth = sizes[2];
+ // kapton leads the larger dimensions of the foil
+ // (including the cited small distance from Z=0 stave reference plane)
+ // the thickness is the sum of the ones of all components
+ fullLength = kpLength + dist;
+ fullWidth = kpWidth;
+ fullThickness = kpThickness + alThickness + g0Thickness + g1Thickness;
+ // create the container
+// TGeoMedium *air = GetMedium("AIR$", mgr);
+ TGeoVolumeAssembly *container = new TGeoVolumeAssembly(Form("ITSSPDgFOIL-%s",suf));
+// TGeoVolume *container = mgr->MakeBox(Form("ITSSPDgFOIL-%s",suf),
+// air, 0.5*fullThickness, 0.5*fullWidth, 0.5*fullLength);
+ // create the common correction rotation (which depends of what side
+ // we are building)
+ TGeoRotation *rotCorr = new TGeoRotation(*gGeoIdentity);
+ if (isRight) rotCorr->RotateY(90.0);
+ else rotCorr->RotateY(-90.0);
+ // compute the translations, which are in the length and
+ // thickness directions
+ Double_t x, y, z, shift = 0.0;
+ if (isRight) shift = dist;
+ // glue (bottom)
+ x = -0.5*(fullThickness - g0Thickness);
+ z = 0.5*(fullLength - kpLength) - shift;
+ TGeoCombiTrans *glTrans0 = new TGeoCombiTrans(x, 0.0, z, rotCorr);
+ // kapton
+ x += 0.5*(g0Thickness + kpThickness);
+ TGeoCombiTrans *kpTrans = new TGeoCombiTrans(x, 0.0, z, rotCorr);
+ // aluminum
+ x += 0.5*(kpThickness + alThickness);
+ z = 0.5*(fullLength - alLength) - shift - 0.5*(kpLength - alLength);
+ TGeoCombiTrans *alTrans = new TGeoCombiTrans(x, 0.0, z, rotCorr);
+ // glue (top)
+ x += 0.5*(alThickness + g1Thickness);
+ z = 0.5*(fullLength - kpLength) - shift;
+ TGeoCombiTrans *glTrans1 = new TGeoCombiTrans(x, 0.0, z, rotCorr);
+
+ //cout << fgkGapHalfStave << endl;
+ //cout << g0Thickness << endl;
+ //cout << kpThickness << endl;
+ //cout << alThickness << endl;
+ //cout << g1Thickness << endl;
+
+ // add to container
+ container->SetLineColor(kMagenta-10);
+ container->AddNode(kpVol, 1, kpTrans);
+ container->AddNode(alVol, 1, alTrans);
+ container->AddNode(g0Vol, 1, glTrans0);
+ container->AddNode(g1Vol, 2, glTrans1);
+ // to add the grease we remember the sizes of the holes, stored as
+ // additional parameters in the kapton layer size:
+ // - sizes[3] = hole length
+ // - sizes[4] = hole width
+ // - sizes[5] = position of first hole center
+ // - sizes[6] = standard separation between holes
+ // - sizes[7] = separation between 5th and 6th hole
+ // - sizes[8] = separation between 10th and 11th hole
+ // - sizes[9] = separation between the upper hole border and
+ // the foil border
+ Double_t holeLength = kpSize[0];
+ Double_t holeWidth = kpSize[1];
+ Double_t holeFirstZ = kpSize[2];
+ Double_t holeSepZ = kpSize[3];
+ Double_t holeSep5th6th = kpSize[4];
+ Double_t holeSep10th11th = kpSize[5];
+ Double_t holeSepY = kpSize[6];
+ // volume (common)
+ // Grease has not been defined to date. Need much more information
+ // no this material!
+ TGeoMedium *grease = GetMedium("SPD KAPTON(POLYCH2)$", mgr); // ??? GREASE
+ TGeoVolume *hVol = mgr->MakeBox("ITSSPDGrease", grease,
+ 0.5*fullThickness, 0.5*holeWidth, 0.5*holeLength);
+ hVol->SetLineColor(kBlue);
+ // displacement of volumes in the container
+ Int_t idx = 1; // copy numbers start from 1.
+ x = 0.0;
+ y = 0.5*(fullWidth - holeWidth) - holeSepY;
+ if (isRight) z = holeFirstZ - 0.5*fullLength + dist;
+ else z = 0.5*fullLength - holeFirstZ - dist;
+ for (Int_t i = 0; i < 11; i++) {
+ TGeoTranslation *t = 0;
+ t = new TGeoTranslation(x, y, -z);
+ container->AddNode(hVol, idx++, t);
+ if (i < 4) shift = holeSepZ;
+ else if (i == 4) shift = holeSep5th6th;
+ else if (i < 9) shift = holeSepZ;
+ else shift = holeSep10th11th;
+ if (isRight) z += shift;
+ else z -= shift;
+ } // end for i
+ return container;
+}
+//___________________________________________________________________
+TGeoVolumeAssembly* AliITSv11GeometrySPD::CreateMCM(Bool_t isRight,
+ TArrayD &sizes, TGeoManager *mgr) const
+{
+ //
+ // Create a TGeoAssembly containing all the components of the MCM.
+ // The TGeoVolume container is rejected due to the possibility of overlaps
+ // when placing this object on the carbon fiber sector.
+ // The assembly contains:
+ // - the thin part of the MCM (integrated circuit)
+ // - the MCM chips (specifications from EDMS)
+ // - the cap which covers the zone where chips are bound to MCM
+ // ---
+ // The local reference frame of this assembly is defined in such a way
+ // that all volumes are contained in a virtual box whose center
+ // is placed exactly in the middle of the occupied space w.r to all
+ // directions. This will ease the positioning of this object in the
+ // half-stave. The sizes of this virtual box are stored in
+ // the array passed by reference.
+ // ---
+ // Arguments:
+ // - a boolean flag to know if this is the "left" or "right" MCM, when
+ // looking at the stave from above (i.e. the direction from which
+ // one sees bus over ladders over grounding foil) and keeping the
+ // continuous border in the upper part, one sees the thicker part
+ // on the left or right.
+ // - an array passed by reference which will contain the size of
+ // the virtual container.
+ // - a pointer to the used TGeoManager.
+ //
+
+ // to distinguish the "left" and "right" objects, a suffix is created
+ char suf[5];
+ if (isRight) strcpy(suf, "R"); else strcpy(suf, "L");
+
+ // ** MEDIA **
+ TGeoMedium *medBase = GetMedium("SPD KAPTON(POLYCH2)$",mgr);// ??? MCM BASE
+ TGeoMedium *medChip = GetMedium("SPD SI CHIP$",mgr);
+ TGeoMedium *medCap = GetMedium("AL$",mgr);
+
+ // The shape of the MCM is divided into 3 sectors with different
+ // widths (Y) and lengths (X), like in this sketch:
+ //
+ // 0 1 2
+ // +---------------------+-----------------------------------+
+ // | 4 sect 2 |
+ // | 6 sect 1 /-------------------+
+ // | sect 0 /--------------/ 3
+ // +--------------------/ 5
+ // 8 7
+ //
+ // the inclination of all oblique borders (6-7, 4-5) is always 45 degrees.
+ // From drawings we can parametrize the dimensions of all these sectors,
+ // then the shape of this part of the MCM is implemented as a
+ // TGeoXtru centerd in the virtual XY space.
+ // The first step is definig the relevant sizes of this shape:
+ Int_t i, j;
+ Double_t mcmThickness = fgkmm * 0.35;
+ Double_t sizeXtot = fgkmm * 105.6; // total distance (0-2)
+ // resp. 7-8, 5-6 and 3-4
+ Double_t sizeXsector[3] = {fgkmm * 28.4, fgkmm * 41.4, fgkmm * 28.8};
+ // resp. 0-8, 1-6 and 2-3
+ Double_t sizeYsector[3] = {fgkmm * 15.0, fgkmm * 11.0, fgkmm * 8.0};
+ Double_t sizeSep01 = fgkmm * 4.0; // x(6)-x(7)
+ Double_t sizeSep12 = fgkmm * 3.0; // x(4)-x(5)
+
+ // define sizes of chips (last is the thickest)
+ Double_t chipLength[5] = { 4.00, 6.15, 3.85, 5.60, 18.00 };
+ Double_t chipWidth[5] = { 3.00, 4.10, 3.85, 5.60, 5.45 };
+ Double_t chipThickness[5] = { 0.60, 0.30, 0.30, 1.00, 1.20 };
+ TString name[5];
+ name[0] = "ITSSPDanalog";
+ name[1] = "ITSSPDpilot";
+ name[2] = "ITSSPDgol";
+ name[3] = "ITSSPDrx40";
+ name[4] = "ITSSPDoptical";
+ Color_t color[5] = { kCyan, kGreen, kYellow, kBlue, kOrange };
+
+ // define the sizes of the cover
+ Double_t capThickness = fgkmm * 0.3;
+ Double_t capHeight = fgkmm * 1.7;
+
+ // compute the total size of the virtual container box
+ sizes.Set(3);
+ Double_t &thickness = sizes[0];
+ Double_t &length = sizes[1];
+ Double_t &width = sizes[2];
+ length = sizeXtot;
+ width = sizeYsector[0];
+ thickness = mcmThickness + capHeight;
+
+ // define all the relevant vertices of the polygon
+ // which defines the transverse shape of the MCM.
+ // These values are used to several purposes, and
+ // for each one, some points must be excluded
+ Double_t xRef[9], yRef[9];
+ xRef[0] = -0.5*sizeXtot;
+ yRef[0] = 0.5*sizeYsector[0];
+ xRef[1] = xRef[0] + sizeXsector[0] + sizeSep01;
+ yRef[1] = yRef[0];
+ xRef[2] = -xRef[0];
+ yRef[2] = yRef[0];
+ xRef[3] = xRef[2];
+ yRef[3] = yRef[2] - sizeYsector[2];
+ xRef[4] = xRef[3] - sizeXsector[2];
+ yRef[4] = yRef[3];
+ xRef[5] = xRef[4] - sizeSep12;
+ yRef[5] = yRef[4] - sizeSep12;
+ xRef[6] = xRef[5] - sizeXsector[1];
+ yRef[6] = yRef[5];
+ xRef[7] = xRef[6] - sizeSep01;
+ yRef[7] = yRef[6] - sizeSep01;
+ xRef[8] = xRef[0];
+ yRef[8] = -yRef[0];
+
+ // the above points are defined for the "right" MCM (if ve view the
+ // stave from above) in order to change to the "left" one, we must
+ // change the sign to all X values:
+ if (isRight) for (i = 0; i < 9; i++) xRef[i] = -xRef[i];
+
+ // the shape of the MCM and glue layer are done excluding point 1,
+ // which is not necessary and cause the geometry builder to get confused
+ j = 0;
+ Double_t xBase[8], yBase[8];
+ for (i = 0; i < 9; i++) {
+ if (i == 1) continue;
+ xBase[j] = xRef[i];
+ yBase[j] = yRef[i];
+ j++;
+ } // end for i
+
+ // the MCM cover is superimposed over the zones 1 and 2 only
+ Double_t xCap[6], yCap[6];
+ j = 0;
+ for (i = 1; i <= 6; i++) {
+ xCap[j] = xRef[i];
+ yCap[j] = yRef[i];
+ j++;
+ } // end for i
+
+ // define positions of chips,
+ // which must be added to the bottom-left corner of MCM
+ // and divided by 1E4;
+ Double_t chipX[5], chipY[5];
+ if (isRight) {
+ chipX[0] = 666320.;
+ chipX[1] = 508320.;
+ chipX[2] = 381320.;
+ chipX[3] = 295320.;
+ chipX[4] = 150320.;
+ chipY[0] = 23750.;
+ chipY[1] = 27750.;
+ chipY[2] = 20750.;
+ chipY[3] = 42750.;
+ chipY[4] = 39750.;
+ } else {
+ chipX[0] = 389730.;
+ chipX[1] = 548630.;
+ chipX[2] = 674930.;
+ chipX[3] = 761430.;
+ chipX[4] = 905430.;
+ chipY[0] = 96250.;
+ chipY[1] = 91950.;
+ chipY[2] = 99250.;
+ chipY[3] = 107250.;
+ chipY[4] = 109750.;
+ } // end if isRight
+ for (i = 0; i < 5; i++) {
+ chipX[i] *= 0.00001;
+ chipY[i] *= 0.00001;
+ if (isRight) {
+ chipX[i] += xRef[3];
+ chipY[i] += yRef[3];
+ } else {
+ chipX[i] += xRef[8];
+ chipY[i] += yRef[8];
+ } // end for isRight
+ chipLength[i] *= fgkmm;
+ chipWidth[i] *= fgkmm;
+ chipThickness[i] *= fgkmm;
+ } // end for i
+
+ // create shapes for MCM
+ Double_t z1, z2;
+ TGeoXtru *shBase = new TGeoXtru(2);
+ z1 = -0.5*thickness;
+ z2 = z1 + mcmThickness;
+ shBase->DefinePolygon(8, xBase, yBase);
+ shBase->DefineSection(0, z1, 0., 0., 1.0);
+ shBase->DefineSection(1, z2, 0., 0., 1.0);
+
+ // create volumes of MCM
+ TGeoVolume *volBase = new TGeoVolume("ITSSPDbase", shBase, medBase);
+ volBase->SetLineColor(kRed);
+
+ // to create the border of the MCM cover, it is required the
+ // subtraction of two shapes the outer is created using the
+ // reference points defined here
+ TGeoXtru *shCapOut = new TGeoXtru(2);
+ shCapOut->SetName(Form("ITSSPDshCAPOUT%s", suf));
+ z1 = z2;
+ z2 = z1 + capHeight - capThickness;
+ shCapOut->DefinePolygon(6, xCap, yCap);
+ shCapOut->DefineSection(0, z1, 0., 0., 1.0);
+ shCapOut->DefineSection(1, z2, 0., 0., 1.0);
+ // the inner is built similarly but subtracting the thickness
+ Double_t angle, cs;
+ Double_t xin[6], yin[6];
+ if (!isRight) {
+ angle = 45.0;
+ cs = TMath::Cos( 0.5*(TMath::Pi() - angle*TMath::DegToRad()) );
+ xin[0] = xCap[0] + capThickness;
+ yin[0] = yCap[0] - capThickness;
+ xin[1] = xCap[1] - capThickness;
+ yin[1] = yin[0];
+ xin[2] = xin[1];
+ yin[2] = yCap[2] + capThickness;
+ xin[3] = xCap[3] - capThickness*cs;
+ yin[3] = yin[2];
+ xin[4] = xin[3] - sizeSep12;
+ yin[4] = yCap[4] + capThickness;
+ xin[5] = xin[0];
+ yin[5] = yin[4];
+ } else {
+ angle = 45.0;
+ cs = TMath::Cos( 0.5*(TMath::Pi() - angle*TMath::DegToRad()) );
+ xin[0] = xCap[0] - capThickness;
+ yin[0] = yCap[0] - capThickness;
+ xin[1] = xCap[1] + capThickness;
+ yin[1] = yin[0];
+ xin[2] = xin[1];
+ yin[2] = yCap[2] + capThickness;
+ xin[3] = xCap[3] - capThickness*cs;
+ yin[3] = yin[2];
+ xin[4] = xin[3] + sizeSep12;
+ yin[4] = yCap[4] + capThickness;
+ xin[5] = xin[0];
+ yin[5] = yin[4];
+ } // end if !isRight
+ TGeoXtru *shCapIn = new TGeoXtru(2);
+ shCapIn->SetName(Form("ITSSPDshCAPIN%s", suf));
+ shCapIn->DefinePolygon(6, xin, yin);
+ shCapIn->DefineSection(0, z1 - 0.01, 0., 0., 1.0);
+ shCapIn->DefineSection(1, z2 + 0.01, 0., 0., 1.0);
+ // compose shapes
+ TGeoCompositeShape *shCapBorder = new TGeoCompositeShape(
+ Form("ITSSPDshBORDER%s", suf),
+ Form("%s-%s", shCapOut->GetName(),
+ shCapIn->GetName()));
+ // create volume
+ TGeoVolume *volCapBorder = new TGeoVolume("ITSSPDcapBoarder",
+ shCapBorder,medCap);
+ volCapBorder->SetLineColor(kGreen);
+ // finally, we create the top of the cover, which has the same
+ // shape of outer border and a thickness equal of the one othe
+ // cover border one
+ TGeoXtru *shCapTop = new TGeoXtru(2);
+ z1 = z2;
+ z2 = z1 + capThickness;
+ shCapTop->DefinePolygon(6, xCap, yCap);
+ shCapTop->DefineSection(0, z1, 0., 0., 1.0);
+ shCapTop->DefineSection(1, z2, 0., 0., 1.0);
+ TGeoVolume *volCapTop = new TGeoVolume("ITSSPDcapTop", shCapTop, medCap);
+ volCapTop->SetLineColor(kBlue);
+
+ // create container assembly with right suffix
+ TGeoVolumeAssembly *mcmAssembly = new TGeoVolumeAssembly(
+ Form("ITSSPDmcm%s", suf));
+
+ // add mcm layer
+ mcmAssembly->AddNode(volBase, 1, gGeoIdentity);
+ // add chips
+ for (i = 0; i < 5; i++) {
+ TGeoVolume *box = gGeoManager->MakeBox(name[i],medChip,
+ 0.5*chipLength[i], 0.5*chipWidth[i], 0.5*chipThickness[i]);
+ TGeoTranslation *tr = new TGeoTranslation(chipX[i],chipY[i],
+ 0.5*(-thickness + chipThickness[i]) + mcmThickness);
+ box->SetLineColor(color[i]);
+ mcmAssembly->AddNode(box, 1, tr);
+ } // end for i
+ // add cap border
+ mcmAssembly->AddNode(volCapBorder, 1, gGeoIdentity);
+ // add cap top
+ mcmAssembly->AddNode(volCapTop, 1, gGeoIdentity);
+
+ return mcmAssembly;
+}
+
+/*
+//__________________________________________________________________________________________
+TGeoVolumeAssembly* AliITSv11GeometrySPD::CreatePixelBus
+(Bool_t isRight, TArrayD &sizes, TGeoManager *mgr) const
+{
+ //
+ // The pixel bus is implemented as a TGeoBBox with some objects on it,
+ // which could affect the particle energy loss.
+ // ---
+ // In order to avoid confusion, the bus is directly displaced
+ // according to the axis orientations which are used in the final stave:
+ // X --> thickness direction
+ // Y --> width direction
+ // Z --> length direction
+ //
+
+
+ // ** MEDIA **
+
+ //PIXEL BUS
+ TGeoMedium *medBus = GetMedium("SPDBUS(AL+KPT+EPOX)$",mgr);
+ TGeoMedium *medPt1000 = GetMedium("CERAMICS$",mgr); // ??? PT1000
+ // Capacity
+ TGeoMedium *medCap = GetMedium("SDD X7R capacitors$",mgr);
+ // ??? Resistance
+ // TGeoMedium *medRes = GetMedium("SDD X7R capacitors$",mgr);
+ TGeoMedium *medRes = GetMedium("ALUMINUM$",mgr);
+ TGeoMedium *medExt = GetMedium("SDDKAPTON (POLYCH2)$", mgr);
+ // ** SIZES & POSITIONS **
+ Double_t busLength = 170.501 * fgkmm; // length of plane part
+ Double_t busWidth = 13.800 * fgkmm; // width
+ Double_t busThickness = 0.280 * fgkmm; // thickness
+ Double_t pt1000Length = fgkmm * 1.50;
+ Double_t pt1000Width = fgkmm * 3.10;
+ Double_t pt1000Thickness = fgkmm * 0.60;
+ Double_t pt1000Y, pt1000Z[10];// position of the pt1000's along the bus
+ Double_t capLength = fgkmm * 2.55;
+ Double_t capWidth = fgkmm * 1.50;
+ Double_t capThickness = fgkmm * 1.35;
+ Double_t capY[2], capZ[2];
+
+ Double_t resLength = fgkmm * 2.20;
+ Double_t resWidth = fgkmm * 0.80;
+ Double_t resThickness = fgkmm * 0.35;
+ Double_t resY[2], resZ[2];
+
+ Double_t extThickness = fgkmm * 0.25;
+ Double_t ext1Length = fgkmm * (26.7 - 10.0);
+ Double_t ext2Length = fgkmm * (285.0 - ext1Length + extThickness);
+ Double_t extWidth = fgkmm * 11.0;
+ Double_t extHeight = fgkmm * 2.5;
+
+
+ // position of pt1000, resistors and capacitors depends on the
+ // bus if it's left or right one
+ if (!isRight) {
+ pt1000Y = 64400.;
+ pt1000Z[0] = 66160.;
+ pt1000Z[1] = 206200.;
+ pt1000Z[2] = 346200.;
+ pt1000Z[3] = 486200.;
+ pt1000Z[4] = 626200.;
+ pt1000Z[5] = 776200.;
+ pt1000Z[6] = 916200.;
+ pt1000Z[7] = 1056200.;
+ pt1000Z[8] = 1196200.;
+ pt1000Z[9] = 1336200.;
+ resZ[0] = 1397500.;
+ resY[0] = 26900.;
+ resZ[1] = 682500.;
+ resY[1] = 27800.;
+ capZ[0] = 1395700.;
+ capY[0] = 45700.;
+ capZ[1] = 692600.;
+ capY[1] = 45400.;
+ } else {
+ pt1000Y = 66100.;
+ pt1000Z[0] = 319700.;
+ pt1000Z[1] = 459700.;
+ pt1000Z[2] = 599700.;
+ pt1000Z[3] = 739700.;
+ pt1000Z[4] = 879700.;
+ pt1000Z[5] = 1029700.;
+ pt1000Z[6] = 1169700.;
+ pt1000Z[7] = 1309700.;
+ pt1000Z[8] = 1449700.;
+ pt1000Z[9] = 1589700.;
+ capY[0] = 44500.;
+ capZ[0] = 266700.;
+ capY[1] = 44300.;
+ capZ[1] = 974700.;
+ resZ[0] = 266500.;
+ resY[0] = 29200.;
+ resZ[1] = 974600.;
+ resY[1] = 29900.;
+ } // end if isRight
+ Int_t i;
+ pt1000Y *= 1E-4 * fgkmm;
+ for (i = 0; i < 10; i++) {
+ pt1000Z[i] *= 1E-4 * fgkmm;
+ if (i < 2) {
+ capZ[i] *= 1E-4 * fgkmm;
+ capY[i] *= 1E-4 * fgkmm;
+ resZ[i] *= 1E-4 * fgkmm;
+ resY[i] *= 1E-4 * fgkmm;
+ } // end if iM2
+ } // end for i
+
+ Double_t &fullLength = sizes[1];
+ Double_t &fullWidth = sizes[2];
+ Double_t &fullThickness = sizes[0];
+ fullLength = busLength;
+ fullWidth = busWidth;
+ // add the thickness of the thickest component on bus (capacity)
+ fullThickness = busThickness + capThickness;
+ // ** VOLUMES **
+ TGeoVolumeAssembly *container = new TGeoVolumeAssembly("PixelBus");
+ TGeoVolume *bus = mgr->MakeBox("Bus", medBus, 0.5*busThickness, 0.5*busWidth, 0.5*busLength);
+ TGeoVolume *pt1000 = mgr->MakeBox("PT1000", medPt1000, 0.5*pt1000Thickness, 0.5*pt1000Width, 0.5*pt1000Length);
+ TGeoVolume *res = mgr->MakeBox("Resistor", medRes, 0.5*resThickness, 0.5*resWidth, 0.5*resLength);
+ TGeoVolume *cap = mgr->MakeBox("Capacitor", medCap, 0.5*capThickness, 0.5*capWidth, 0.5*capLength);
+ TGeoVolume *ext1 = mgr->MakeBox("Extender1", medExt, 0.5*extThickness, 0.5*extWidth, 0.5*ext1Length);
+ TGeoVolume *ext2 = mgr->MakeBox("Extender2", medExt, 0.5*extHeight - extThickness, 0.5*extWidth, 0.5*extThickness);
+ TGeoVolume *ext3 = mgr->MakeBox("Extender3", medExt, extThickness, 0.5*extWidth, 0.5*ext2Length);
+ bus->SetLineColor(kYellow + 2);
+ pt1000->SetLineColor(kGreen + 3);
+ res->SetLineColor(kRed + 1);
+ cap->SetLineColor(kBlue - 7);
+ ext1->SetLineColor(kGray);
+ ext2->SetLineColor(kGray);
+ ext3->SetLineColor(kGray);
+
+ // ** MOVEMENTS AND POSITIONEMENT **
+ // bus
+ TGeoTranslation *trBus = new TGeoTranslation(0.5 * (busThickness -
+ fullThickness), 0.0, 0.0);
+ container->AddNode(bus, 0, trBus);
+ Double_t zRef, yRef, x, y, z;
+ if (isRight) {
+ zRef = -0.5*fullLength;
+ yRef = -0.5*fullWidth;
+ } else {
+ zRef = -0.5*fullLength;
+ yRef = -0.5*fullWidth;
+ } // end if isRight
+ // pt1000
+ x = 0.5*(pt1000Thickness - fullThickness) + busThickness;
+ for (i = 0; i < 10; i++) {
+ y = yRef + pt1000Y;
+ z = zRef + pt1000Z[i];
+ TGeoTranslation *tr = new TGeoTranslation(x, y, z);
+ container->AddNode(pt1000, i, tr);
+ } // end for i
+ // capacitors
+ x = 0.5*(capThickness - fullThickness) + busThickness;
+ for (i = 0; i < 2; i++) {
+ y = yRef + capY[i];
+ z = zRef + capZ[i];
+ TGeoTranslation *tr = new TGeoTranslation(x, y, z);
+ container->AddNode(cap, i, tr);
+ } // end for i
+ // resistors
+ x = 0.5*(resThickness - fullThickness) + busThickness;
+ for (i = 0; i < 2; i++) {
+ y = yRef + resY[i];
+ z = zRef + resZ[i];
+ TGeoTranslation *tr = new TGeoTranslation(x, y, z);
+ container->AddNode(res, i, tr);
+ } // end for i
+ // extender
+ if (isRight) {
+ y = 0.5 * (-fullWidth + extWidth);
+ z = 0.5 * (-fullLength + fgkmm * 10.0);
+ }
+ else {
+ y = 0.5 * (fullWidth - extWidth);
+ z = 0.5 * ( fullLength - fgkmm * 10.0);
+ }
+ x = 0.5 * (extThickness - fullThickness) + busThickness;
+ //y = 0.5 * (fullWidth - extWidth);
+ TGeoTranslation *trExt1 = new TGeoTranslation(x, y, z);
+ if (isRight) {
+ z -= 0.5 * (ext1Length - extThickness);
+ }
+ else {
+ z += 0.5 * (ext1Length - extThickness);
+ }
+ x += 0.5*(extHeight - extThickness);
+ TGeoTranslation *trExt2 = new TGeoTranslation(x, y, z);
+ if (isRight) {
+ z -= 0.5 * (ext2Length - extThickness);
+ }
+ else {
+ z += 0.5 * (ext2Length - extThickness);
+ }
+ x += 0.5*(extHeight - extThickness) + extThickness;
+ TGeoTranslation *trExt3 = new TGeoTranslation(x, y, z);
+ container->AddNode(ext1, 0, trExt1);
+ container->AddNode(ext2, 0, trExt2);
+ container->AddNode(ext3, 0, trExt3);
+
+
+ sizes[3] = yRef + pt1000Y;
+ sizes[4] = zRef + pt1000Z[2];
+ sizes[5] = zRef + pt1000Z[7];
+
+ return container;
+}
+*/
+
+//______________________________________________________________________
+TGeoVolumeAssembly* AliITSv11GeometrySPD::CreatePixelBus
+(Bool_t isRight, Int_t ilayer, TArrayD &sizes, TGeoManager *mgr) const
+{
+ //
+ // The pixel bus is implemented as a TGeoBBox with some objects on it,
+ // which could affect the particle energy loss.
+ // ---
+ // In order to avoid confusion, the bus is directly displaced
+ // according to the axis orientations which are used in the final stave:
+ // X --> thickness direction
+ // Y --> width direction
+ // Z --> length direction
+ //
+
+ // ** CRITICAL CHECK ******************************************************
+ // layer number can be ONLY 1 or 2
+ if (ilayer != 1 && ilayer != 2) AliFatal("Layer number MUST be 1 or 2");
+
+ // ** MEDIA **
+ //PIXEL BUS
+ TGeoMedium *medBus = GetMedium("SPDBUS(AL+KPT+EPOX)$",mgr);
+ TGeoMedium *medPt1000 = GetMedium("CERAMICS$",mgr); // ??? PT1000
+ // Capacity
+ TGeoMedium *medCap = GetMedium("SDD X7R capacitors$",mgr);
+ // ??? Resistance
+ //TGeoMedium *medRes = GetMedium("SDD X7R capacitors$",mgr);
+ TGeoMedium *medRes = GetMedium("ALUMINUM$",mgr);
+ TGeoMedium *medExt = GetMedium("SDDKAPTON (POLYCH2)$", mgr);
+ // ** SIZES & POSITIONS **
+ Double_t busLength = 170.501 * fgkmm; // length of plane part
+ Double_t busWidth = 13.800 * fgkmm; // width
+ Double_t busThickness = 0.280 * fgkmm; // thickness
+ Double_t pt1000Length = fgkmm * 1.50;
+ Double_t pt1000Width = fgkmm * 3.10;
+ Double_t pt1000Thickness = fgkmm * 0.60;
+ Double_t pt1000Y, pt1000Z[10];// position of the pt1000's along the bus
+ Double_t capLength = fgkmm * 2.55;
+ Double_t capWidth = fgkmm * 1.50;
+ Double_t capThickness = fgkmm * 1.35;
+ Double_t capY[2], capZ[2];
+
+ Double_t resLength = fgkmm * 2.20;
+ Double_t resWidth = fgkmm * 0.80;
+ Double_t resThickness = fgkmm * 0.35;
+ Double_t resY[2], resZ[2];
+
+ Double_t extThickness = fgkmm * 0.25;
+ Double_t ext1Length = fgkmm * (26.7 - 10.0);
+ Double_t ext2Length = fgkmm * 284.0 - ext1Length + extThickness;
+ Double_t extWidth = fgkmm * 11.0;
+ Double_t extHeight = fgkmm * 2.5;
+
+ // position of pt1000, resistors and capacitors depends on the
+ // bus if it's left or right one
+ if (!isRight) {
+ pt1000Y = 64400.;
+ pt1000Z[0] = 66160.;
+ pt1000Z[1] = 206200.;
+ pt1000Z[2] = 346200.;
+ pt1000Z[3] = 486200.;
+ pt1000Z[4] = 626200.;
+ pt1000Z[5] = 776200.;
+ pt1000Z[6] = 916200.;
+ pt1000Z[7] = 1056200.;
+ pt1000Z[8] = 1196200.;
+ pt1000Z[9] = 1336200.;
+ resZ[0] = 1397500.;
+ resY[0] = 26900.;
+ resZ[1] = 682500.;
+ resY[1] = 27800.;
+ capZ[0] = 1395700.;
+ capY[0] = 45700.;
+ capZ[1] = 692600.;
+ capY[1] = 45400.;
+ } else {
+ pt1000Y = 66100.;
+ pt1000Z[0] = 319700.;
+ pt1000Z[1] = 459700.;
+ pt1000Z[2] = 599700.;
+ pt1000Z[3] = 739700.;
+ pt1000Z[4] = 879700.;
+ pt1000Z[5] = 1029700.;
+ pt1000Z[6] = 1169700.;
+ pt1000Z[7] = 1309700.;
+ pt1000Z[8] = 1449700.;
+ pt1000Z[9] = 1589700.;
+ capY[0] = 44500.;
+ capZ[0] = 266700.;
+ capY[1] = 44300.;
+ capZ[1] = 974700.;
+ resZ[0] = 266500.;
+ resY[0] = 29200.;
+ resZ[1] = 974600.;
+ resY[1] = 29900.;
+ } // end if isRight
+ Int_t i;
+ pt1000Y *= 1E-4 * fgkmm;
+ for (i = 0; i < 10; i++) {
+ pt1000Z[i] *= 1E-4 * fgkmm;
+ if (i < 2) {
+ capZ[i] *= 1E-4 * fgkmm;
+ capY[i] *= 1E-4 * fgkmm;
+ resZ[i] *= 1E-4 * fgkmm;
+ resY[i] *= 1E-4 * fgkmm;
+ } // end if iM2
+ } // end for i
+
+ Double_t &fullLength = sizes[1];
+ Double_t &fullWidth = sizes[2];
+ Double_t &fullThickness = sizes[0];
+ fullLength = busLength;
+ fullWidth = busWidth;
+ // add the thickness of the thickest component on bus (capacity)
+ fullThickness = busThickness + capThickness;
+
+ // ** VOLUMES **
+ TGeoVolumeAssembly *container = new TGeoVolumeAssembly("ITSSPDpixelBus");
+ TGeoVolume *bus = mgr->MakeBox("ITSSPDbus", medBus, 0.5*busThickness,
+ 0.5*busWidth, 0.5*busLength);
+ TGeoVolume *pt1000 = mgr->MakeBox("ITSSPDpt1000",medPt1000,
+ 0.5*pt1000Thickness,0.5*pt1000Width, 0.5*pt1000Length);
+ TGeoVolume *res = mgr->MakeBox("ITSSPDresistor", medRes, 0.5*resThickness,
+ 0.5*resWidth, 0.5*resLength);
+ TGeoVolume *cap = mgr->MakeBox("ITSSPDcapacitor", medCap, 0.5*capThickness,
+ 0.5*capWidth, 0.5*capLength);
+
+ TGeoVolume *ext1 = mgr->MakeBox("Extender1", medExt, 0.5*extThickness, 0.5*extWidth, 0.5*ext1Length);
+ TGeoVolume *ext2 = mgr->MakeBox("Extender2", medExt, 0.5*extHeight - 2.*extThickness, 0.5*extWidth, 0.5*extThickness);
+ TGeoVolume *ext3 = mgr->MakeBox("Extender3", medExt, 0.5*extThickness, 0.5*(extWidth-0.8*fgkmm), 0.5*ext2Length + extThickness); // Hardcode fix of a small overlap
+ bus->SetLineColor(kYellow + 2);
+ pt1000->SetLineColor(kGreen + 3);
+ res->SetLineColor(kRed + 1);
+ cap->SetLineColor(kBlue - 7);
+ ext1->SetLineColor(kGray);
+ ext2->SetLineColor(kGray);
+ ext3->SetLineColor(kGray);
+
+ // ** MOVEMENTS AND POSITIONEMENT **
+ // bus
+ TGeoTranslation *trBus = new TGeoTranslation(0.5 * (busThickness -
+ fullThickness), 0.0, 0.0);
+ container->AddNode(bus, 1, trBus);
+ Double_t zRef, yRef, x, y, z;
+ if (isRight) {
+ zRef = -0.5*fullLength;
+ yRef = -0.5*fullWidth;
+ } else {
+ zRef = -0.5*fullLength;
+ yRef = -0.5*fullWidth;
+ } // end if isRight
+ // pt1000
+ x = 0.5*(pt1000Thickness - fullThickness) + busThickness;
+ for (i = 0; i < 10; i++) {
+ y = yRef + pt1000Y;
+ z = zRef + pt1000Z[i];
+ TGeoTranslation *tr = new TGeoTranslation(x, y, z);
+ container->AddNode(pt1000, i+1, tr);
+ } // end for i
+ // capacitors
+ x = 0.5*(capThickness - fullThickness) + busThickness;
+ for (i = 0; i < 2; i++) {
+ y = yRef + capY[i];
+ z = zRef + capZ[i];
+ TGeoTranslation *tr = new TGeoTranslation(x, y, z);
+ container->AddNode(cap, i+1, tr);
+ } // end for i
+ // resistors
+ x = 0.5*(resThickness - fullThickness) + busThickness;
+ for (i = 0; i < 2; i++) {
+ y = yRef + resY[i];
+ z = zRef + resZ[i];
+ TGeoTranslation *tr = new TGeoTranslation(x, y, z);
+ container->AddNode(res, i+1, tr);
+ } // end for i
+
+ // extender
+ if (ilayer == 2) {
+ if (isRight) {
+ y = 0.5 * (fullWidth - extWidth) - 0.1;
+ z = 0.5 * (-fullLength + fgkmm * 10.0);
+ }
+ else {
+ y = 0.5 * (fullWidth - extWidth) - 0.1;
+ z = 0.5 * ( fullLength - fgkmm * 10.0);
+ }
+ }
+ else {
+ if (isRight) {
+ y = -0.5 * (fullWidth - extWidth);
+ z = 0.5 * (-fullLength + fgkmm * 10.0);
+ }
+ else {
+ y = -0.5 * (fullWidth - extWidth);
+ z = 0.5 * ( fullLength - fgkmm * 10.0);
+ }
+ }
+ x = 0.5 * (extThickness - fullThickness) + busThickness;
+ //y = 0.5 * (fullWidth - extWidth);
+ TGeoTranslation *trExt1 = new TGeoTranslation(x, y, z);
+ if (isRight) {
+ z -= 0.5 * (ext1Length - extThickness);
+ }
+ else {
+ z += 0.5 * (ext1Length - extThickness);
+ }
+ x += 0.5*(extHeight - 3.*extThickness);
+ TGeoTranslation *trExt2 = new TGeoTranslation(x, y, z);
+ if (isRight) {
+ z -= 0.5 * (ext2Length - extThickness) + 2.5*extThickness;
+ }
+ else {
+ z += 0.5 * (ext2Length - extThickness) + 2.5*extThickness;
+ }
+ x += 0.5*(extHeight - extThickness) - 2.*extThickness;
+ TGeoTranslation *trExt3 = new TGeoTranslation(x, y, z);
+ container->AddNode(ext1, 0, trExt1);
+ container->AddNode(ext2, 0, trExt2);
+ container->AddNode(ext3, 0, trExt3);
+
+ sizes[3] = yRef + pt1000Y;
+ sizes[4] = zRef + pt1000Z[2];
+ sizes[5] = zRef + pt1000Z[7];
+
+ return container;
+}
+
+//______________________________________________________________________
+TList* AliITSv11GeometrySPD::CreateConeModule(TGeoManager *mgr) const
+{
+ TGeoMedium *medInox = GetMedium("INOX$",mgr);
+ TGeoMedium *medExt = GetMedium("SDDKAPTON (POLYCH2)$", mgr);
+ TGeoMedium *medPlate = GetMedium("SPD C (M55J)$", mgr);
+
+ Double_t extThickness = fgkmm * 0.25;
+ Double_t ext1Length = fgkmm * (26.7 - 10.0);
+ Double_t ext2Length = fgkmm * (285.0 - ext1Length + extThickness);
+
+ Double_t cableThickness = 1.5 * fgkmm;
+ Double_t cableL1 = 350.0 * fgkmm - extThickness - ext1Length - ext2Length;
+ Double_t cableL2 = 340.0 * fgkmm;
+ //Double_t cableL3 = 570.0 * fgkmm;
+ Double_t cableL3 = 57.0 * fgkmm;
+ Double_t cableW1 = 11.0 * fgkmm;
+ Double_t cableW2 = 30.0 * fgkmm;
+ Double_t cableW3 = 50.0 * fgkmm;
+
+ Double_t mcmThickness = 1.2 *fgkmm;
+ Double_t mcmLength = cableL1 + cableL2 + cableL3;
+ Double_t mcmWidth = cableW1;
+
+ Double_t plateLength = 200.0 * fgkmm;
+ Double_t plateWidth = 50.0 * fgkmm;
+ Double_t plateThickness = 5.0 * fgkmm;
+
+ Double_t x[12], y[12];
+
+ x[0] = 7.5;
+ y[0] = 0.0 + 0.5 * cableW1;
+
+ x[1] = x[0] + cableL1 - 0.5*(cableW2 - cableW1);
+ y[1] = y[0];
+
+ x[2] = x[0] + cableL1;
+ y[2] = y[1] + 0.5*(cableW2 - cableW1);
+
+ x[3] = x[2] + cableL2;
+ y[3] = y[2];
+
+ x[4] = x[3] + 0.5*(cableW3 - cableW2);
+ y[4] = y[3] + 0.5*(cableW3 - cableW2);
+
+ x[5] = x[4] + cableL3 - 0.5*(cableW3 - cableW2);
+ y[5] = y[4];
+
+ for (Int_t i = 6; i < 12; i++) {
+ x[i] = x[11 - i];
+ y[i] = -y[11 - i];
+ }
+
+ TGeoVolumeAssembly* container[2];
+ container[0] = new TGeoVolumeAssembly("ITSSPDConeModule");
+ container[1] = new TGeoVolumeAssembly("ITSSPDCoolingModule");
+
+ TGeoXtru *shCable = new TGeoXtru(2);
+ shCable->DefinePolygon(12, x, y);
+ shCable->DefineSection(0, 0., 0., 0., 1.0);
+ shCable->DefineSection(1, cableThickness, 0., 0., 1.0);
+
+ TGeoVolume *volCable = new TGeoVolume("ITSSPDExtender", shCable, medExt);
+ volCable->SetLineColor(kGreen);
+
+ TGeoVolume *volTube = gGeoManager->MakeTube("ITSSPDCoolingTubeCone", medInox, 5.*fgkmm, 6.*fgkmm, 0.5*(x[5] - x[0]));
+ volTube->SetLineColor(kGray);
+
+ Double_t thickness = cableThickness + mcmThickness;
+ TGeoBBox *shOut = new TGeoBBox("ITSSPD_shape_plateout", 0.5*plateThickness, 0.5*plateLength, 0.5*plateWidth);
+ TGeoBBox *shIn = new TGeoBBox("ITSSPD_shape_platein", 0.5*thickness, 0.52*plateLength, 0.5*cableW2);
+ Char_t string[255];
+ sprintf(string, "%s-%s", shOut->GetName(), shIn->GetName());
+ TGeoCompositeShape *shPlate = new TGeoCompositeShape("ITSSPDPlate_shape", string);
+ TGeoVolume *volPlate = new TGeoVolume("ITSSPDPlate", shPlate, medPlate);
+ volPlate->SetLineColor(kRed);
+
+ TGeoVolume *volMCMExt = gGeoManager->MakeBox("ITSSPDextenderMCM", medExt, 0.5*mcmThickness, 0.5*mcmLength, 0.5*mcmWidth);
+ volMCMExt->SetLineColor(kGreen+3);
+
+ TGeoRotation *rot = new TGeoRotation(*gGeoIdentity);
+ rot->RotateX(90.0);
+ rot->RotateZ(90.0);
+ container[0]->AddNode(volCable, 0, rot);
+
+ TGeoTranslation *combi = new TGeoTranslation(cableThickness + 0.5*mcmThickness, x[0] + 0.5*mcmLength, 0.0);
+ container[0]->AddNode(volMCMExt, 0, combi);
+
+ TGeoRotation *rot1 = new TGeoRotation(*gGeoIdentity);
+ rot1->RotateX(87.5);
+ TGeoCombiTrans *tr = new TGeoCombiTrans(1.15, x[0] + 0.5*(x[5] - x[0]), -2.95, rot1);
+ container[1]->AddNode(volTube, 0, tr);
+
+ TGeoTranslation *tr1 = new TGeoTranslation(0.5*plateThickness - 0.5*(plateThickness-thickness), x[3] - x[0] - 0.52*plateLength, 0.0);
+ container[0]->AddNode(volPlate, 0, tr1);
+
+ TList* conemodulelist = new TList();
+
+ conemodulelist->Add(container[0]);
+ conemodulelist->Add(container[1]);
+
+ return conemodulelist;
+}
+
+//______________________________________________________________________
+void AliITSv11GeometrySPD::CreateCones(TGeoVolume *moth) const
+{
+
+ TList* modulelist = CreateConeModule(gGeoManager);
+ TGeoVolumeAssembly* module;
+
+ //Double_t angle[10] = {18., 54., 90., 126., 162., -18., -54., -90., -126., -162.};
+ // angleNm for cone modules (cables), angleNc for cooling tubes
+ Double_t angle1m[10] = {18., 54., 90., 129., 165., 201.0, 237.0, 273.0, 309.0, 345.0};
+ Double_t angle2m[10] = {18., 53., 90., 126., 162., 198.0, 233.0, 270.0, 309.0, 342.0};
+ Double_t angle1c[10] = {18., 54., 90., 124., 165., 201.0, 237.0, 273.0, 304.0, 345.0};
+ Double_t angle2c[10] = {18., 44., 90., 126., 162., 198.0, 223.0, 270.0, 309.0, 342.0};
+
+ // First add the cables
+ module = (TGeoVolumeAssembly*)modulelist->At(0);
+ for (Int_t i = 0; i < 10; i++) {
+ TGeoRotation *rot1 = new TGeoRotation(*gGeoIdentity);
+ rot1->RotateY(-90.0);
+ rot1->RotateX(45.0);
+ angle1m[i] -= 1.5;
+ rot1->RotateZ(90.0 - angle1m[i]);
+ TGeoCombiTrans *tr1 = new TGeoCombiTrans(0.0, 0.0, 38.0, rot1);
+ moth->AddNode(module, 2*i, tr1);
+ TGeoRotation *rot2 = new TGeoRotation(*gGeoIdentity);
+ rot2->RotateY(90.0);
+ rot2->RotateX(-45.0);
+ angle2m[i] -= 1.5;
+ rot2->RotateZ(90.0 - angle2m[i]);
+ TGeoCombiTrans *tr2 = new TGeoCombiTrans(0.0, 0.0, -37.9, rot2);
+ moth->AddNode(module, 2*i+1, tr2);
+ }
+
+ // Then the cooling tubes
+ module = (TGeoVolumeAssembly*)modulelist->At(1);
+ for (Int_t i = 0; i < 10; i++) {
+ TGeoRotation *rot1 = new TGeoRotation(*gGeoIdentity);
+ rot1->RotateY(-90.0);
+ rot1->RotateX(45.0);
+ angle1c[i] -= 1.5;
+ rot1->RotateZ(90.0 - angle1c[i]);
+ TGeoCombiTrans *tr1 = new TGeoCombiTrans(0.0, 0.0, 38.0, rot1);
+ moth->AddNode(module, 2*i, tr1);
+ TGeoRotation *rot2 = new TGeoRotation(*gGeoIdentity);
+ rot2->RotateY(90.0);
+ rot2->RotateX(-45.0);
+ angle2c[i] -= 1.5;
+ rot2->RotateZ(90.0 - angle2c[i]);
+ TGeoCombiTrans *tr2 = new TGeoCombiTrans(0.0, 0.0, -37.9, rot2);
+ moth->AddNode(module, 2*i+1, tr2);
+ }
+}
+
+//______________________________________________________________________
+TGeoVolume* AliITSv11GeometrySPD::CreateExtender(
+ const Double_t *extenderParams, const TGeoMedium *extenderMedium,
+ TArrayD& sizes) const
+{
+ //
+ // ------------------ CREATE AN EXTENDER ------------------------
+ //
+ // This function creates the following picture (in plane xOy)
+ // Should be useful for the definition of the pixel bus and MCM extenders
+ // The origin corresponds to point 0 on the picture, at half-width
+ // in Z direction
+ //
+ // Y 7 6 5
+ // ^ +---+---------------------+
+ // | / |
+ // | / |
+ // 0------> X / +---------------------+
+ // / / 3 4
+ // / /
+ // 9 8 / /
+ // +-----------+ /
+ // | /
+ // | /
+ // ---> +-----------+---+
+ // | 0 1 2
+ // |
+ // origin (0,0,0)
+ //
+ //
+ // Takes 6 parameters in the following order :
+ // |--> par 0 : inner length [0-1] / [9-8]
+ // |--> par 1 : thickness ( = [0-9] / [4-5])
+ // |--> par 2 : angle of the slope
+ // |--> par 3 : total height in local Y direction
+ // |--> par 4 : outer length [3-4] / [6-5]
+ // |--> par 5 : width in local Z direction
+ //
+ Double_t slopeDeltaX = (extenderParams[3] - extenderParams[1]
+ * TMath::Cos(extenderParams[2])) /
+ TMath::Tan(extenderParams[2]);
+ Double_t extenderXtruX[10] = {
+ 0 ,
+ extenderParams[0] ,
+ extenderParams[0]+extenderParams[1]*TMath::Sin(extenderParams[2]) ,
+ extenderParams[0]+extenderParams[1]*TMath::Sin(extenderParams[2])+
+ slopeDeltaX ,
+ extenderParams[0]+extenderParams[1]*TMath::Sin(extenderParams[2])+
+ slopeDeltaX + extenderParams[4],
+ extenderParams[0]+extenderParams[1]*TMath::Sin(extenderParams[2])+
+ slopeDeltaX + extenderParams[4],
+ extenderParams[0]+extenderParams[1]*TMath::Sin(extenderParams[2])+
+ slopeDeltaX ,
+ extenderParams[0]+extenderParams[1]*TMath::Sin(extenderParams[2])+
+ slopeDeltaX - extenderParams[1] * TMath::Sin(extenderParams[2]) ,
+ extenderParams[0] ,
+ 0
+ };
+ Double_t extenderXtruY[10] = {
+ 0 ,
+ 0 ,
+ extenderParams[1] * (1-TMath::Cos(extenderParams[2])) ,
+ extenderParams[3] - extenderParams[1] ,
+ extenderParams[3] - extenderParams[1] ,
+ extenderParams[3] ,
+ extenderParams[3] ,
+ extenderParams[3]-extenderParams[1]*(1-TMath::Cos(extenderParams[2])) ,
+ extenderParams[1] ,
+ extenderParams[1]
+ };
+
+ if (sizes.GetSize() != 3) sizes.Set(3);
+ Double_t &thickness = sizes[0];
+ Double_t &length = sizes[1];
+ Double_t &width = sizes[2];
+
+ thickness = extenderParams[3];
+ width = extenderParams[5];
+ length = extenderParams[0]+extenderParams[1]*
+ TMath::Sin(extenderParams[2])+slopeDeltaX+extenderParams[4];
+
+ // creation of the volume
+ TGeoXtru *extenderXtru = new TGeoXtru(2);
+ TGeoVolume *extenderXtruVol = new TGeoVolume("ITSSPDextender",extenderXtru,
+ extenderMedium);
+ extenderXtru->DefinePolygon(10,extenderXtruX,extenderXtruY);
+ extenderXtru->DefineSection(0,-0.5*extenderParams[4]);
+ extenderXtru->DefineSection(1, 0.5*extenderParams[4]);
+ return extenderXtruVol;
+}
+//______________________________________________________________________
+TGeoVolumeAssembly* AliITSv11GeometrySPD::CreatePixelBusAndExtensions
+(Bool_t /*zpos*/, TGeoManager *mgr) const
+{
+ //
+ // Creates an assembly which contains the pixel bus and its extension
+ // and the extension of the MCM.
+ // By: Renaud Vernet
+ // NOTE: to be defined its material and its extension in the outside
+ // direction
+ //
+ // ==== constants =====
+ //get the media
+ // PIXEL BUS
+ //TGeoMedium *medPixelBus = GetMedium("SPDBUS(AL+KPT+EPOX)$",mgr);
+ // IXEL BUS EXTENDER
+ TGeoMedium *medPBExtender = GetMedium("SDDKAPTON (POLYCH2)$",mgr);
+ //MCM EXTENDER
+ TGeoMedium *medMCMExtender = GetMedium("SDDKAPTON (POLYCH2)$",mgr);
+ // //geometrical constants
+ const Double_t kPbextenderThickness = 0.07 * fgkmm;
+ //design=?? 70 deg. seems OK
+ const Double_t kPbExtenderSlopeAngle = 70.0 * TMath::Pi()/180.;
+ // = 2.6 - (0.28+0.05+0.35) cf design
+ const Double_t kPbExtenderHeight = 1.92 * fgkmm;
+ const Double_t kPbExtenderWidthY = 11.0 * fgkmm;
+ //design=?? 70 deg. seems OK
+ const Double_t kMcmExtenderSlopeAngle = 70.0 * TMath::Pi()/180.;
+ const Double_t kMcmExtenderThickness = 0.10 * fgkmm;
+ const Double_t kMcmExtenderHeight = 1.8 * fgkmm;
+ const Double_t kMcmExtenderWidthY = kPbExtenderWidthY;
+ // const Double_t groundingThickness = 0.07 * fgkmm;
+ // const Double_t grounding2pixelBusDz = 0.625 * fgkmm;
+ // const Double_t pixelBusThickness = 0.28 * fgkmm;
+ // const Double_t groundingWidthX = 170.501 * fgkmm;
+ // const Double_t pixelBusContactDx = 1.099 * fgkmm;
+ // const Double_t pixelBusWidthY = 13.8 * fgkmm;
+ //design=20 deg.
+ // const Double_t pixelBusContactPhi = 20.0 * TMath::Pi()/180.
+ // const Double_t pbExtenderTopZ = 2.72 * fgkmm;
+ // const Double_t mcmThickness = 0.35 * fgkmm;
+ // const Double_t halfStaveTotalLength = 247.64 * fgkmm;
+ // const Double_t deltaYOrigin = 15.95/2.* fgkmm;
+ // const Double_t deltaXOrigin = 1.1 * fgkmm;
+ // const Double_t deltaZOrigin = halfStaveTotalLength / 2.;
+ // const Double_t grounding2pixelBusDz2 = grounding2pixelBusDz+
+ // groundingThickness/2. + pixelBusThickness/2.;
+ // const Double_t pixelBusWidthX = groundingWidthX;
+ // const Double_t pixelBusRaiseLength = (pixelBusContactDx-
+ // pixelBusThickness*TMath::Sin(pixelBusContactPhi))/
+ // TMath::Cos(pixelBusContactPhi);
+ // const Double_t pbExtenderBaseZ = grounding2pixelBusDz2 +
+ // pixelBusRaiseLength*TMath::Sin(pixelBusContactPhi) +
+ // 2*pixelBusThickness*TMath::Sin(pixelBusContactPhi)*
+ // TMath::Tan(pixelBusContactPhi);
+ // const Double_t pbExtenderDeltaZ = pbExtenderTopZ-pbExtenderBaseZ;
+ // const Double_t pbExtenderEndPointX = 2*deltaZOrigin -
+ // groundingWidthX - 2*pixelBusThickness*TMath::Sin(pixelBusContactPhi);
+ // const Double_t pbExtenderXtru3L = 1.5 * fgkmm; //arbitrary ?
+ // const Double_t pbExtenderXtru4L = (pbExtenderDeltaZ +
+ // pixelBusThickness*(TMath::Cos(extenderSlope)-2))/
+ // TMath::Sin(extenderSlope);
+ // const Double_t kMcmExtenderEndPointX = deltaZOrigin - 48.2 * fgkmm;
+ // const Double_t kMcmExtenderXtru3L = 1.5 * fgkmm;
+ // //===== end constants =====
+ const Double_t kPbExtenderInnerLength = 10. * fgkmm;
+ const Double_t kPbExtenderOuterLength = 15. * fgkmm;
+ const Double_t kMcmExtenderInnerLength = 10. * fgkmm;
+ const Double_t kMcmExtenderOuterLength = 15. * fgkmm;
+ Double_t pbExtenderParams[6] = {kPbExtenderInnerLength, //0
+ kPbextenderThickness, //1
+ kPbExtenderSlopeAngle, //2
+ kPbExtenderHeight, //3
+ kPbExtenderOuterLength, //4
+ kPbExtenderWidthY}; //5
+
+ Double_t mcmExtenderParams[6] = {kMcmExtenderInnerLength, //0
+ kMcmExtenderThickness, //1
+ kMcmExtenderSlopeAngle, //2
+ kMcmExtenderHeight, //3
+ kMcmExtenderOuterLength, //4
+ kMcmExtenderWidthY}; //5
+
+ TArrayD sizes(3);
+ TGeoVolume* pbExtender = CreateExtender(pbExtenderParams,medPBExtender,
+ sizes);
+ if(GetDebug(1))printf("CREATED AN EXTENDER : THICKNESS = %5.5f cm\t"
+ "LENGTH=%5.5f cm\tWIDTH=%5.5f cm\n",sizes[0],sizes[1],sizes[2]);
+ TGeoVolume* mcmExtender = CreateExtender(mcmExtenderParams,medMCMExtender,
+ sizes);
+ if(GetDebug(1))printf("CREATED AN EXTENDER : THICKNESS = %5.5f cm\t"
+ "LENGTH=%5.5f cm\tWIDTH=%5.5f cm\n",sizes[0],sizes[1],sizes[2]);
+ // Double_t pixelBusValues[5] = {pixelBusWidthX, //0
+ // pixelBusThickness, //1
+ // pixelBusContactPhi, //2
+ // pixelBusRaiseLength, //3
+ // pixelBusWidthY}; //4
+
+ // Double_t pbExtenderValues[8] = {pixelBusRaiseLength, //0
+ // pixelBusContactPhi, //1
+ // pbExtenderXtru3L, //2
+ // pixelBusThickness, //3
+ // extenderSlope, //4
+ // pbExtenderXtru4L, //5
+ // pbExtenderEndPointX, //6
+ // kPbExtenderWidthY}; //7
+
+ // Double_t mcmExtenderValues[6] = {mcmExtenderXtru3L, //0
+ // mcmExtenderThickness, //1
+ // extenderSlope, //2
+ // deltaMcmMcmExtender, //3
+ // mcmExtenderEndPointX, //4
+ // mcmExtenderWidthY}; //5
+ // TGeoVolumeAssembly *pixelBus=new TGeoVolumeAssembly("ITSSPDpixelBus");
+ // CreatePixelBus(pixelBus,pixelBusValues,medPixelBus);
+ // TGeoVolumeAssembly *pbExtender = new TGeoVolumeAssembly(
+ // "ITSSPDpixelBusExtender");
+ // CreatePixelBusExtender(pbExtender,pbExtenderValues,medPBExtender);
+ // TGeoVolumeAssembly *mcmExtender = new TGeoVolumeAssembly(
+ // "ITSSPDmcmExtender");
+ // CreateMCMExtender(mcmExtender,mcmExtenderValues,medMCMExtender);
+ //-------------- DEFINITION OF GEOMETRICAL TRANSFORMATIONS --------
+ // TGeoRotation * commonRot = new TGeoRotation("commonRot",0,90,0);
+ // commonRot->MultiplyBy(new TGeoRotation("rot",-90,0,0));
+ // TGeoTranslation * pixelBusTrans = new TGeoTranslation(
+ // pixelBusThickness/2. - deltaXOrigin + 0.52*fgkmm ,
+ // -pixelBusWidthY/2. + deltaYOrigin ,
+ // -groundingWidthX/2. + deltaZOrigin);
+ // TGeoRotation *pixelBusRot = new TGeoRotation(*commonRot);
+ // TGeoTranslation *pbExtenderTrans =new TGeoTranslation(*pixelBusTrans);
+ // TGeoRotation *pbExtenderRot = new TGeoRotation(*pixelBusRot);
+ // pbExtenderTrans->SetDz(*(pbExtenderTrans->GetTranslation()+2) -
+ // pixelBusWidthX/2. - 2*pixelBusThickness*
+ // TMath::Sin(pixelBusContactPhi));
+ // if (!zpos) {
+ // pbExtenderTrans->SetDy(*(pbExtenderTrans->GetTranslation()+1) -
+ // (pixelBusWidthY - kPbExtenderWidthY)/2.);
+ // } else {
+ // pbExtenderTrans->SetDy(*(pbExtenderTrans->GetTranslation()+1) +
+ // (pixelBusWidthY - kPbExtenderWidthY)/2.);
+ // }
+ // pbExtenderTrans->SetDx(*(pbExtenderTrans->GetTranslation()) +
+ // pixelBusThickness/2 + 2*pixelBusThickness*
+ // TMath::Sin(pixelBusContactPhi)*
+ // TMath::Tan(pixelBusContactPhi));
+ // TGeoTranslation * mcmExtenderTrans = new TGeoTranslation(0.12*fgkmm +
+ // mcmThickness - deltaXOrigin,
+ // pbExtenderTrans->GetTranslation()[1],
+ // -4.82);
+ // TGeoRotation * mcmExtenderRot = new TGeoRotation(*pbExtenderRot);
+ // // add pt1000 components
+ // Double_t pt1000Z = fgkmm * 64400. * 1E-4;
+ // //Double_t pt1000X[10] = {319700., 459700., 599700., 739700.,
+ // 879700., 1029700., 1169700., 1309700.,
+ // 1449700., 1589700.};
+ // Double_t pt1000X[10] ={66160., 206200., 346200., 486200., 626200.,
+ // 776200., 916200., 1056200., 1196200., 1336200.};
+ // Double_t pt1000size[3] = {fgkmm*1.5, fgkmm*0.6, fgkmm*3.1};
+ // Int_t i;
+ // for (i = 0; i < 10; i++) {
+ // pt1000X[i] *= fgkmm * 1E-4;
+ // }
+ // TGeoVolume *pt1000 = mgr->MakeBox("ITSSPDpt1000",0,0.5*pt1000size[0],
+ // 0.5*pt1000size[1], 0.5*pt1000size[2]);
+ // pt1000->SetLineColor(kGray);
+ // Double_t refThickness = - pixelBusThickness;
+ // for (i = 0; i < 10; i++) {
+ // TGeoTranslation *tr = new TGeoTranslation(pt1000X[i]-
+ // 0.5*pixelBusWidthX, 0.002+0.5*(-3.*refThickness+pt1000size[3]),
+ // pt1000Z -0.5*pixelBusWidthY);
+ // pixelBus->AddNode(pt1000, i+1, tr);
+ // }
+
+ //CREATE FINAL VOLUME ASSEMBLY AND ROTATE IT
+ TGeoVolumeAssembly *assembly = new TGeoVolumeAssembly("ITSSPDextenders");
+ // assembly->AddNode((TGeoVolume*)pixelBus,1,
+ // new TGeoCombiTrans(*pixelBusTrans,*pixelBusRot));
+ // assembly->AddNode((TGeoVolume*)pbExtender,1,
+ // new TGeoCombiTrans(*pbExtenderTrans,*pbExtenderRot));
+ // assembly->AddNode((TGeoVolume*)mcmExtender,1,
+ // new TGeoCombiTrans(*mcmExtenderTrans,*mcmExtenderRot));
+ // assembly->AddNode(mcmExtender,1,new TGeoIdentity());
+ assembly->AddNode(pbExtender,1);
+ assembly->AddNode(mcmExtender,1);
+ // assembly->SetTransparency(50);
+
+ return assembly;
+}
+//______________________________________________________________________
+TGeoVolumeAssembly* AliITSv11GeometrySPD::CreateHalfStave(Bool_t isRight,
+Int_t layer,Int_t idxCentral,Int_t idxSide,TArrayD &sizes,TGeoManager *mgr)
+{
+ //
+ // Implementation of an half-stave, which depends on the side where
+ // we are on the stave. The convention for "left" and "right" is the
+ // same as for the MCM. The return value is a TGeoAssembly which is
+ // structured in such a way that the origin of its local reference
+ // frame coincides with the origin of the whole stave.
+ // The TArrayD passed by reference will contain details of the shape:
+ // - sizes[0] = thickness
+ // - sizes[1] = length
+ // - sizes[2] = width
+ // - sizes[3] = common 'x' position for eventual clips
+ // - sizes[4] = common 'y' position for eventual clips
+ // - sizes[5] = 'z' position of first clip
+ // - sizes[6] = 'z' position of second clip
+ //
+
+ // ** CHECK **
+
+ // idxCentral and idxSide must be different
+ if (idxCentral == idxSide) {
+ AliInfo("Ladders must be inserted in half-stave with "
+ "different indexes.");
+ idxSide = idxCentral + 1;
+ AliInfo(Form("Central ladder will be inserted with index %d",
+ idxCentral));
+ AliInfo(Form("Side ladder will be inserted with index %d",idxSide));
+ } // end if
+
+ // define the separations along Z direction between the objects
+ Double_t sepLadderLadder = fgkmm * 0.2; // sep. btw the 2 ladders
+ Double_t sepLadderCenter = fgkmm * 0.4; // sep. btw the "central" ladder
+ // and the Z=0 plane in stave ref.
+ Double_t sepLadderMCM = fgkmm * 0.3; // sep. btw the "external" ladder
+ // and MCM
+ Double_t sepBusCenter = fgkmm * 0.3; // sep. btw the bus central edge
+ // and the Z=0 plane in stave ref.
+
+ // ** VOLUMES **
+
+ // grounding foil
+ TArrayD grndSize(3);
+ // This one line repalces the 3 bellow, BNS.
+ TGeoVolume *grndVol = CreateGroundingFoil(isRight, grndSize, mgr);
+ Double_t &grndThickness = grndSize[0];
+ Double_t &grndLength = grndSize[1];
+
+ // ladder
+ TArrayD ladderSize(3);
+ TGeoVolume *ladder = CreateLadder(layer, ladderSize, mgr);
+ Double_t ladderThickness = ladderSize[0];
+ Double_t ladderLength = ladderSize[1];
+ Double_t ladderWidth = ladderSize[2];
+
+ // MCM
+ TArrayD mcmSize(3);
+ TGeoVolumeAssembly *mcm = CreateMCM(!isRight,mcmSize,mgr);
+ Double_t mcmThickness = mcmSize[0];
+ Double_t mcmLength = mcmSize[1];
+ Double_t mcmWidth = mcmSize[2];
+
+ // bus
+ TArrayD busSize(6);
+ TGeoVolumeAssembly *bus = CreatePixelBus(isRight, layer, busSize, mgr);
+ Double_t busThickness = busSize[0];
+ Double_t busLength = busSize[1];
+ Double_t busWidth = busSize[2];
+
+ // glue between ladders and pixel bus
+ TGeoMedium *medLadGlue = GetMedium("EPOXY$", mgr);
+ Double_t ladGlueThickness = fgkmm * 0.1175 - fgkGapLadder;
+ TGeoVolume *ladderGlue = mgr->MakeBox("ITSSPDladderGlue",medLadGlue,
+ 0.5*ladGlueThickness, 0.5*busWidth, 0.5*busLength);
+ ladderGlue->SetLineColor(kYellow + 5);
+
+ // create references for the whole object, as usual
+ sizes.Set(7);
+ Double_t &fullThickness = sizes[0];
+ Double_t &fullLength = sizes[1];
+ Double_t &fullWidth = sizes[2];
+
+ // compute the full size of the container
+ fullLength = sepLadderCenter+2.0*ladderLength+sepLadderMCM+
+ sepLadderLadder+mcmLength;
+ fullWidth = ladderWidth;
+ fullThickness = grndThickness + fgkGapLadder + mcmThickness + busThickness;
+ //cout << "HSTAVE FULL THICKNESS = " << fullThickness << endl;
+
+ // ** MOVEMENTS **
+
+ // grounding foil (shifted only along thickness)
+ Double_t xGrnd = -0.5*fullThickness + 0.5*grndThickness;
+ Double_t zGrnd = -0.5*grndLength;
+ if (!isRight) zGrnd = -zGrnd;
+ TGeoTranslation *grndTrans = new TGeoTranslation(xGrnd, 0.0, zGrnd);
+
+ // ladders (translations along thickness and length)
+ // layers must be sorted going from the one at largest Z to the
+ // one at smallest Z:
+ // -|Zmax| ------> |Zmax|
+ // 3 2 1 0
+ // then, for layer 1 ladders they must be placed exactly this way,
+ // and in layer 2 at the opposite. In order to remember the placements,
+ // we define as "inner" and "outer" ladder respectively the one close
+ // to barrel center, and the one closer to MCM, respectively.
+ Double_t xLad, zLadIn, zLadOut;
+ xLad = xGrnd + 0.5*(grndThickness + ladderThickness) +
+ 0.01175 - fgkGapLadder;
+ zLadIn = -sepLadderCenter - 0.5*ladderLength;
+ zLadOut = zLadIn - sepLadderLadder - ladderLength;
+ if (!isRight) {
+ zLadIn = -zLadIn;
+ zLadOut = -zLadOut;
+ } // end if !isRight
+ TGeoRotation *rotLad = new TGeoRotation(*gGeoIdentity);
+ rotLad->RotateZ(90.0);
+ rotLad->RotateY(180.0);
+ Double_t sensWidth = fgkmm * 12.800;
+ Double_t chipWidth = fgkmm * 15.950;
+ Double_t guardRingWidth = fgkmm * 0.560;
+ Double_t ladderShift = 0.5 * (chipWidth - sensWidth - 2.0*guardRingWidth);
+ TGeoCombiTrans *trLadIn = new TGeoCombiTrans(xLad,ladderShift,zLadIn,
+ rotLad);
+ TGeoCombiTrans *trLadOut = new TGeoCombiTrans(xLad,ladderShift,zLadOut,
+ rotLad);
+
+ // MCM (length and thickness direction, placing at same level as the
+ // ladder, which implies to recompute the position of center, because
+ // ladder and MCM have NOT the same thickness) the two copies of the
+ // MCM are placed at the same distance from the center, on both sides
+ Double_t xMCM = xGrnd + 0.5*grndThickness + 0.5*mcmThickness +
+ 0.01175 - fgkGapLadder;
+ Double_t yMCM = 0.5*(fullWidth - mcmWidth);
+ Double_t zMCM = zLadOut - 0.5*ladderLength - 0.5*mcmLength - sepLadderMCM;
+ if (!isRight) zMCM = zLadOut + 0.5*ladderLength + 0.5*mcmLength +
+ sepLadderMCM;
+
+ // create the correction rotations
+ TGeoRotation *rotMCM = new TGeoRotation(*gGeoIdentity);
+ rotMCM->RotateY(90.0);
+ TGeoCombiTrans *trMCM = new TGeoCombiTrans(xMCM, yMCM, zMCM, rotMCM);
+
+ // glue between ladders and pixel bus
+ Double_t xLadGlue = xLad + 0.5*ladderThickness + 0.01175 -
+ fgkGapLadder + 0.5*ladGlueThickness;
+
+ // bus (length and thickness direction)
+ Double_t xBus = xLadGlue + 0.5*ladGlueThickness + 0.5*busThickness;
+ Double_t yBus = 0.5*(fullWidth - busWidth) + 0.075; // Hardcode fix of a small overlap
+ Double_t zBus = -0.5*busLength - sepBusCenter;
+ if (!isRight) zBus = -zBus;
+ TGeoTranslation *trBus = new TGeoTranslation(xBus, yBus, zBus);
+
+ TGeoTranslation *trLadGlue = new TGeoTranslation(xLadGlue, 0.0, zBus);
+
+ // create the container
+ TGeoVolumeAssembly *container = 0;
+ if (idxCentral+idxSide==5) {
+ container = new TGeoVolumeAssembly("ITSSPDhalf-Stave1");
+ } else {
+ container = new TGeoVolumeAssembly("ITSSPDhalf-Stave0");
+ } // end if
+
+ // add to container all objects
+ container->AddNode(grndVol, 1, grndTrans);
+ // ladders are inserted in different order to respect numbering scheme
+ // which is inverted when going from outer to inner layer
+ container->AddNode(ladder, idxCentral+1, trLadIn);
+ container->AddNode(ladder, idxSide+1, trLadOut);
+ container->AddNode(ladderGlue, 1, trLadGlue);
+ container->AddNode(mcm, 1, trMCM);
+ container->AddNode(bus, 1, trBus);
+
+ // since the clips are placed in correspondence of two pt1000s,
+ // their position is computed here, but they are not added by default
+ // it will be the StavesInSector method which will decide to add them
+ // anyway, to recovery some size informations on the clip, it must be
+ // created
+ TArrayD clipSize;
+ // TGeoVolume *clipDummy = CreateClip(clipSize, kTRUE, mgr);
+ CreateClip(clipSize, kTRUE, mgr);
+ // define clip movements (width direction)
+ sizes[3] = xBus + 0.5*busThickness;
+ sizes[4] = 0.5 * (fullWidth - busWidth) - clipSize[6] - fgkmm*0.48;
+ sizes[5] = zBus + busSize[4];
+ sizes[6] = zBus + busSize[5];
+
+ return container;
+}
+//______________________________________________________________________
+TGeoVolumeAssembly* AliITSv11GeometrySPD::CreateStave(Int_t layer,
+ TArrayD &sizes, TGeoManager *mgr)
+{
+ //
+ // This method uses all other ones which create pieces of the stave
+ // and assemblies everything together, in order to return the whole
+ // stave implementation, which is returned as a TGeoVolumeAssembly,
+ // due to the presence of some parts which could generate fake overlaps
+ // when put on the sector.
+ // This assembly contains, going from bottom to top in the thickness
+ // direction:
+ // - the complete grounding foil, defined by the "CreateGroundingFoil"
+ // method which already joins some glue and real groudning foil
+ // layers for the whole stave (left + right);
+ // - 4 ladders, which are sorted according to the ALICE numbering
+ // scheme, which depends on the layer we are building this stave for;
+ // - 2 MCMs (a left and a right one);
+ // - 2 pixel buses (a left and a right one);
+ // ---
+ // Arguments:
+ // - the layer number, which determines the displacement and naming
+ // of sensitive volumes
+ // - a TArrayD passed by reference which will contain the size
+ // of virtual box containing the stave
+ // - the TGeoManager
+ //
+
+ // create the container
+ TGeoVolumeAssembly *container = new TGeoVolumeAssembly(Form(
+ "ITSSPDlay%d-Stave",layer));
+ // define the indexes of the ladders in order to have the correct order
+ // keeping in mind that the staves will be inserted as they are on layer
+ // 2, while they are rotated around their local Y axis when inserted
+ // on layer 1, so in this case they must be put in the "wrong" order
+ // to turn out to be right at the end. The convention is:
+ // -|Zmax| ------> |Zmax|
+ // 3 2 1 0
+ // with respect to the "native" stave reference frame, "left" is in
+ // the positive Z this leads the definition of these indexes:
+ Int_t idxCentralL, idxSideL, idxCentralR, idxSideR;
+
+ if (layer == 1) {
+ idxSideL = 3;
+ idxCentralL = 2;
+ idxCentralR = 1;
+ idxSideR = 0;
+ } else {
+ idxSideL = 0;
+ idxCentralL = 1;
+ idxCentralR = 2;
+ idxSideR = 3;
+ } // end if layer ==1
+
+ // create the two half-staves
+ TArrayD sizeL, sizeR;
+ TGeoVolumeAssembly *hstaveL = CreateHalfStave(kFALSE, layer, idxCentralL,
+ idxSideL, sizeL,mgr);
+ TGeoVolumeAssembly *hstaveR = CreateHalfStave(kTRUE, layer, idxCentralR,
+ idxSideR, sizeR, mgr);
+ // copy the size to the stave's one
+ sizes.Set(9);
+ sizes[0] = sizeL[0];
+ sizes[1] = sizeR[1] + sizeL[1];
+ sizes[2] = sizeL[2];
+ sizes[3] = sizeL[3];
+ sizes[4] = sizeL[4];
+ sizes[5] = sizeL[5];
+ sizes[6] = sizeL[6];
+ sizes[7] = sizeR[5];
+ sizes[8] = sizeR[6];
+
+ // add to container all objects
+ container->AddNode(hstaveL, 1);
+ container->AddNode(hstaveR, 1);
+
+ return container;
+}
+//______________________________________________________________________
+void AliITSv11GeometrySPD::SetAddStave(Bool_t *mask)
+{
+ //
+ // Define a mask which states qhich staves must be placed.
+ // It is a string which must contain '0' or '1' depending if
+ // a stave must be placed or not.
+ // Each place is referred to one of the staves, so the first
+ // six characters of the string will be checked.
+ //
+ Int_t i;
+
+ for (i = 0; i < 6; i++) fAddStave[i] = mask[i];
+}
+//______________________________________________________________________
+void AliITSv11GeometrySPD::StavesInSector(TGeoVolume *moth, TGeoManager *mgr)
+{
+ //
+ // Unification of essentially two methods:
+ // - the one which creates the sector structure
+ // - the one which returns the complete stave
+ // ---
+ // For compatibility, this method requires the same arguments
+ // asked by "CarbonFiberSector" method, which is recalled here.
+ // Like this cited method, this one does not return any value,
+ // but it inserts in the mother volume (argument 'moth') all the stuff
+ // which composes the complete SPD sector.
+ // ---
+ // In the following, the stave numbering order used for arrays is the
+ // same as defined in the GetSectorMountingPoints():
+ // /5
+ // /\/4
+ // 1\ \/3
+ // 0|___\/2
+ // ---
+ // Arguments: see description of "CarbonFiberSector" method.
+ //
+
+ Double_t shift[6]; // shift from the innermost position in the
+ // sector placement plane (where the stave
+ // edge is in the point where the rounded
+ // corner begins)
+
+ shift[0] = fgkmm * -0.691;
+ shift[1] = fgkmm * 5.041;
+ shift[2] = fgkmm * 1.816;
+ shift[3] = fgkmm * -0.610;
+ shift[4] = fgkmm * -0.610;
+ shift[5] = fgkmm * -0.610;
+
+ // corrections after interaction with Andrea and CAD
+ Double_t corrX[6] = {0.0, 0.0, 0.0, 0.0, 0.0, 0.0};
+ Double_t corrY[6] = {0.0, 0.0, 0.0, 0.0, 0.0, 0.0};
+
+ corrX[0] = 0.0046;
+ corrX[1] = -0.0041;
+ corrX[2] = corrX[3] = corrX[4] = corrX[5] = -0.0016;
+
+ corrY[0] = -0.0007;
+ corrY[1] = -0.0009;
+ corrY[2] = corrY[3] = corrY[4] = corrY[5] = -0.0003;
+
+ corrX[0] += 0.00026;
+ corrY[0] += -0.00080;
+
+ corrX[1] += 0.00018;
+ corrY[1] += -0.00086;
+
+ corrX[2] += 0.00020;
+ corrY[2] += -0.00062;
+
+ corrX[3] += 0.00017;
+ corrY[3] += -0.00076;
+
+ corrX[4] += 0.00016;
+ corrY[4] += -0.00096;
+
+ corrX[5] += 0.00018;
+ corrY[5] += -0.00107;
+
+ // create stave volumes (different for layer 1 and 2)
+ TArrayD staveSizes1(9), staveSizes2(9), clipSize(5);
+ Double_t &staveHeight = staveSizes1[2], &staveThickness = staveSizes1[0];
+ TGeoVolume *stave1 = CreateStave(1, staveSizes1, mgr);
+ TGeoVolume *stave2 = CreateStave(2, staveSizes2, mgr);
+ TGeoVolume *clip = CreateClip(clipSize, kFALSE, mgr);
+
+ Double_t xL, yL; // leftmost edge of mounting point (XY projection)
+ Double_t xR, yR; // rightmost edge of mounting point (XY projection)
+ Double_t xM, yM; // middle point of the segment L-R
+ Double_t dx, dy; // (xL - xR) and (yL - yR)
+ Double_t widthLR; // width of the segment L-R
+ Double_t angle; // stave rotation angle in degrees
+ Double_t diffWidth; // difference between mounting plane width and
+ // stave width (smaller)
+ Double_t xPos, yPos; // final translation of the stave
+ Double_t parMovement; // translation in the LR plane direction
+
+ staveThickness += fgkGapHalfStave;
+
+ // loop on staves
+ Int_t i, iclip = 1;
+ for (i = 0; i < 6; i++) {
+ // in debug mode, if this stave is not required, it is skipped
+ if (!fAddStave[i]) continue;
+ // retrieve reference points
+ GetSectorMountingPoints(i, xL, yL, xR, yR);
+ xM = 0.5 * (xL + xR);
+ yM = 0.5 * (yL + yR);
+ dx = xL - xR;
+ dy = yL - yR;
+ angle = TMath::ATan2(dy, dx);
+ widthLR = TMath::Sqrt(dx*dx + dy*dy);
+ diffWidth = 0.5*(widthLR - staveHeight);
+ // first, a movement along this plane must be done
+ // by an amount equal to the width difference
+ // and then the fixed shift must also be added
+ parMovement = diffWidth + shift[i];
+ // due to stave thickness, another movement must be done
+ // in the direction normal to the mounting plane
+ // which is computed using an internal method, in a reference
+ // frame where the LR segment has its middle point in the origin
+ // and axes parallel to the master reference frame
+ if (i == 0) {
+ ParallelPosition(-0.5*staveThickness, -parMovement, angle,
+ xPos, yPos);
+ } // end if i==0
+ if (i == 1) {
+ ParallelPosition( 0.5*staveThickness, -parMovement, angle,
+ xPos, yPos);
+ }else {
+ ParallelPosition( 0.5*staveThickness, parMovement, angle,
+ xPos, yPos);
+ } // end if i==1
+ // then we go into the true reference frame
+ xPos += xM;
+ yPos += yM;
+ xPos += corrX[i];
+ yPos += corrY[i];
+ // using the parameters found here, compute the
+ // translation and rotation of this stave:
+ TGeoRotation *rot = new TGeoRotation(*gGeoIdentity);
+ if (i == 0 || i == 1) rot->RotateX(180.0);
+ rot->RotateZ(90.0 + angle * TMath::RadToDeg());
+ TGeoCombiTrans *trans = new TGeoCombiTrans(xPos, yPos, 0.0, rot);
+ if (i == 0 || i == 1) {
+ moth->AddNode(stave1, i+1, trans);
+ }else {
+ moth->AddNode(stave2, i - 1, trans);
+ if (i != 2) {
+ // except in the case of stave #2,
+ // clips must be added, and this is done directly on the sector
+ Int_t j;
+ //TArrayD clipSize;
+ TGeoRotation *rotClip = new TGeoRotation(*gGeoIdentity);
+ rotClip->RotateZ(-90.0);
+ rotClip->RotateX(180.0);
+ Double_t x = staveSizes2[3] + fgkGapHalfStave;
+ Double_t y = staveSizes2[4];
+ Double_t z[4] = { staveSizes2[5], staveSizes2[6],
+ staveSizes2[7], staveSizes2[8] };
+ for (j = 0; j < 4; j++) {
+ TGeoCombiTrans *trClip = new TGeoCombiTrans(x, y, z[j],
+ rotClip);
+ *trClip = *trans * *trClip;
+ moth->AddNode(clip, iclip++, trClip);
+ } // end for j
+ } // end if i!=2
+ } // end if i==0||i==1 else
+ } // end for i
+}
+//______________________________________________________________________
+void AliITSv11GeometrySPD::ParallelPosition(Double_t dist1, Double_t dist2,
+ Double_t phi, Double_t &x, Double_t &y) const
+{
+ //
+ // Performs the following steps:
+ // 1 - finds a straight line parallel to the one passing through
+ // the origin and with angle 'phi' with X axis(phi in RADIANS);
+ // 2 - finds another line parallel to the previous one, with a
+ // distance 'dist1' from it
+ // 3 - takes a reference point in the second line in the intersection
+ // between the normal to both lines passing through the origin
+ // 4 - finds a point whith has distance 'dist2' from this reference,
+ // in the second line (point 2)
+ // ----
+ // According to the signs given to dist1 and dist2, the point is
+ // found in different position w.r. to the origin
+ // compute the point
+ //
+ Double_t cs = TMath::Cos(phi);
+ Double_t sn = TMath::Sin(phi);
+
+ x = dist2*cs - dist1*sn;
+ y = dist1*cs + dist2*sn;
+}
+//______________________________________________________________________
+Double_t AliITSv11GeometrySPD::GetSPDSectorTranslation(
+ Double_t x0,Double_t y0,Double_t x1,Double_t y1,Double_t r) const
+{
+ //
+ // Comutes the radial translation of a sector to give the
+ // proper distance between SPD detectors and the beam pipe.
+ // Units in are units out.
+ //
+
+ //Begin_Html
+ /*
+ <A HREF="http://www.physics.ohio-state.edu/HIRG/SoftWareDoc/SPD_Sector_Position.png">
+ Figure showing the geometry used in the computation below. </A>
+ */
+ //End_Html
+
+ // Inputs:
+ // Double_t x0 Point x0 on Sector surface for the inner
+ // most detector mounting
+ // Double_t y0 Point y0 on Sector surface for the innor
+ // most detector mounting
+ // Double_t x1 Point x1 on Sector surface for the inner
+ // most detector mounting
+ // Double_t y1 Point y1 on Sector surface for the innor
+ // most detector mounting
+ // Double_t r The radial distance this mounting surface
+ // should be from the center of the beam pipe.
+ // Outputs:
+ // none.
+ // Return:
+ // The distance the SPD sector should be displaced radialy.
+ //
+ Double_t a,b,c;
+
+ a = x0-x1;
+ if(a==0.0) return 0.0;
+ a = (y0-y1)/a;
+ b = TMath::Sqrt(1.0+a*a);
+ c = y0-a*x0-r*b;
+ return -c;
+}
+//______________________________________________________________________
+void AliITSv11GeometrySPD::CreateFigure0(const Char_t *filepath,
+ const Char_t *type,
+ TGeoManager *mgr) const
+{
+ //
+ // Creates Figure 0 for the documentation of this class. In this
+ // specific case, it creates the X,Y cross section of the SPD suport
+ // section, center and ends. The output is written to a standard
+ // file name to the path specificed.
+ // Inputs:
+ // const Char_t *filepath Path where the figure is to be drawn
+ // const Char_t *type The type of file, default is gif.
+ // TGeoManager *mgr The TGeoManager default gGeoManager
+ // Output:
+ // none.
+ // Return:
+ // none.
+ //
+ TGeoXtru *sA0,*sA1,*sB0,*sB1;
+ //TPolyMarker *pmA,*pmB;
+ TPolyLine plA0,plA1,plB0,plB1;
+ TCanvas *canvas;
+ TLatex txt;
+ Double_t x=0.0,y=0.0;
+ Int_t i,kNRadii=6;
+
+ if(strcmp(filepath,"")){
+ Error("CreateFigure0","filepath=%s type=%s",filepath,type);
+ } // end if
+ //
+ sA0 = (TGeoXtru*) mgr->GetVolume("ITSSPDCarbonFiberSupportSectorA0_1")->
+ GetShape();
+ sA1 = (TGeoXtru*) mgr->GetVolume("ITSSPDCarbonFiberSupportSectorAirA1_1")->
+ GetShape();
+ sB0 = (TGeoXtru*) mgr->GetVolume("ITSSPDCarbonFiberSupportSectorEndB0_1")->
+ GetShape();
+ sB1 = (TGeoXtru*) mgr->GetVolume("ITSSPDCarbonFiberSupportSectorEndAirB1_1"
+ )->GetShape();
+ //pmA = new TPolyMarker();
+ //pmA.SetMarkerStyle(2); // +
+ //pmA.SetMarkerColor(7); // light blue
+ //pmB = new TPolyMarker();
+ //pmB.SetMarkerStyle(5); // X
+ //pmB.SetMarkerColor(6); // purple
+ plA0.SetPolyLine(sA0->GetNvert());
+ plA0.SetLineColor(1); // black
+ plA0.SetLineStyle(1);
+ plA1.SetPolyLine(sA1->GetNvert());
+ plA1.SetLineColor(2); // red
+ plA1.SetLineStyle(1);
+ plB0.SetPolyLine(sB0->GetNvert());
+ plB0.SetLineColor(3); // Green
+ plB0.SetLineStyle(2);
+ plB1.SetPolyLine(sB1->GetNvert());
+ plB1.SetLineColor(4); // Blue
+ plB1.SetLineStyle(2);
+ //for(i=0;i<kNRadii;i++) pmA.SetPoint(i,xyB1p[i][0],xyB1p[i][1]);
+ //for(i=0;i<kNRadii;i++) pmB.SetPoint(i,xyB1p[i][0],xyB1p[i][1]);
+ for(i=0;i<sA0->GetNvert();i++) plA0.SetPoint(i,sA0->GetX(i),sA0->GetY(i));
+ for(i=0;i<sA1->GetNvert();i++) plA1.SetPoint(i,sA1->GetX(i),sA1->GetY(i));
+ for(i=0;i<sB0->GetNvert();i++) plB0.SetPoint(i,sB0->GetX(i),sB0->GetY(i));
+ for(i=0;i<sB1->GetNvert();i++) plB1.SetPoint(i,sB1->GetX(i),sB1->GetY(i));
+ canvas = new TCanvas("AliITSv11GeometrySPDFig0","",1000,1000);
+ canvas->Range(-3.,-3.,3.,3.);
+ txt.SetTextSize(0.05);
+ txt.SetTextAlign(33);
+ txt.SetTextColor(1);
+ txt.DrawLatex(2.9,2.9,"Section A-A outer Carbon Fiber surface");
+ txt.SetTextColor(2);
+ txt.DrawLatex(2.9,2.5,"Section A-A Inner Carbon Fiber surface");
+ txt.SetTextColor(3);
+ txt.DrawLatex(2.9,2.1,"Section E-E outer Carbon Fiber surface");
+ txt.SetTextColor(4);
+ txt.DrawLatex(2.9,1.7,"Section E-E Inner Carbon Fiber surface");
+ plA0.Draw();
+ plA1.Draw();
+ plB0.Draw();
+ plB1.Draw();
+ //pmA.Draw();
+ //pmB.Draw();
+ //
+ x = 1.0;
+ y = -2.5;
+ Char_t chr[3];
+ for(i=0;i<kNRadii;i++){
+ sprintf(chr,"%2d",i);txt.DrawLatex(x-0.1,y,chr);
+ sprintf(chr,"%8.4f",5.000);txt.DrawLatex(x,y,chr);
+ sprintf(chr,"%8.4f",5.000);txt.DrawLatex(x+0.5,y,chr);
+ sprintf(chr,"%8.4f",5.000);txt.DrawLatex(x+1.0,y,chr);
+ sprintf(chr,"%8.4f",5.000);txt.DrawLatex(x+1.5,y,chr);
+ sprintf(chr,"%8.4f",5.000);txt.DrawLatex(x+2.0,y,chr);
+ if(kTRUE) txt.DrawLatex(x+2.5,y,"A-A/E-E");
+ else txt.DrawLatex(x+2.5,y,"E-E");
+ } // end for i
+ txt.DrawLatex(x,y,"x_{c} mm");
+ txt.DrawLatex(x+0.5,y,"y_{c} mm");
+ txt.DrawLatex(x+1.0,y,"R mm");
+ txt.DrawLatex(x+1.5,y,"#theta_{start}^{#circle}");
+ txt.DrawLatex(x+2.0,y,"#theta_{end}^{#circle}");
+ txt.DrawLatex(x+2.5,y,"Section");
+ //
+}
+//______________________________________________________________________
+void AliITSv11GeometrySPD::PrintAscii(ostream *os) const
+{
+ //
+ // Print out class data values in Ascii Form to output stream
+ // Inputs:
+ // ostream *os Output stream where Ascii data is to be writen
+ // Outputs:
+ // none.
+ // Return:
+ // none.
+ //
+ Int_t i,j,k;
+#if defined __GNUC__
+#if __GNUC__ > 2
+ ios::fmtflags fmt = cout.flags();
+#else
+ Int_t fmt;
+#endif
+#else
+#if defined __ICC || defined __ECC || defined __xlC__
+ ios::fmtflags fmt;
+#else
+ Int_t fmt;
+#endif
+#endif
+
+ *os<< fgkGapLadder <<" "<< fgkGapHalfStave<<" "<< 6 <<" ";
+ for(i=0;i<6;i++) *os<< fAddStave[i] <<" "<<fSPDsectorX0.GetSize();
+ for(i=0;i<fSPDsectorX0.GetSize();i++) *os<< fSPDsectorX0.GetAt(i) << " ";
+ for(i=0;i<fSPDsectorX0.GetSize();i++) *os<< fSPDsectorY0.GetAt(i) << " ";
+ for(i=0;i<fSPDsectorX1.GetSize();i++) *os<< fSPDsectorX1.GetAt(i) << " ";
+ for(i=0;i<fSPDsectorX1.GetSize();i++) *os<< fSPDsectorY1.GetAt(i) << " ";
+ *os<<10<<" "<< 2 <<" " << 6 << " "<< 3 <<" ";
+ for(k=0;k<10;k++)for(i=0;i<6;i++)for(j=0;j<3;j++)
+ *os<<fTubeEndSector[k][0][i][j]<<" ";
+ for(k=0;k<10;k++)for(i=0;i<6;i++)for(j=0;j<3;j++)
+ *os<<fTubeEndSector[k][1][i][j]<<" ";
+ os->flags(fmt); // reset back to old Formating.
+ return;
+}
+//
+//______________________________________________________________________
+void AliITSv11GeometrySPD::ReadAscii(istream* is)
+{
+ //
+ // Read in class data values in Ascii Form to output stream
+ // Inputs:
+ // istream *is Input stream where Ascii data is to be read in from
+ // Outputs:
+ // none.
+ // Return:
+ // none.
+ //
+ Int_t i,j,k,n;
+ Double_t gapLadder,GapHalfStave;
+
+ *is>>gapLadder>>GapHalfStave>>n;
+ if(n!=6){
+ Warning("ReadAscii","fAddStave Array !=6 n=%d",n);
+ return;
+ } // end if
+ for(i=0;i<n;i++) *is>>fAddStave[i];
+ *is>>n;
+ fSPDsectorX0.Set(n);
+ fSPDsectorY0.Set(n);
+ fSPDsectorX1.Set(n);
+ fSPDsectorY1.Set(n);
+ for(i=0;i<n;i++) *is>>fSPDsectorX0[i];
+ for(i=0;i<n;i++) *is>>fSPDsectorY0[i];
+ for(i=0;i<n;i++) *is>>fSPDsectorX1[i];
+ for(i=0;i<n;i++) *is>>fSPDsectorY1[i];
+ *is>> i>>j>>n;
+ if(i!=2||j!=6||n!=3){
+ Warning("ReadAscii","fTubeEndSector array wrong size [2][6][3],"
+ "found [%d][%d][%d]",i,j,n);
+ return;
+ } // end if
+ for(k=0;k<10;k++)for(i=0;i<6;i++)for(j=0;j<3;j++)
+ *is>>fTubeEndSector[k][0][i][j];
+ for(k=0;k<10;k++)for(i=0;i<6;i++)for(j=0;j<3;j++)
+ *is>>fTubeEndSector[k][1][i][j];
+ return;
+}
+//
+//______________________________________________________________________
+ostream &operator<<(ostream &os,const AliITSv11GeometrySPD &s)
+{
+ //
+ // Standard output streaming function
+ // Inputs:
+ // ostream &os output steam
+ // AliITSvPPRasymmFMD &s class to be streamed.
+ // Output:
+ // none.
+ // Return:
+ // ostream &os The stream pointer
+ //
+ s.PrintAscii(&os);
+ return os;
+}
+//
+//______________________________________________________________________
+istream &operator>>(istream &is,AliITSv11GeometrySPD &s)
+{
+ //
+ // Standard inputput streaming function
+ // Inputs:
+ // istream &is input steam
+ // AliITSvPPRasymmFMD &s class to be streamed.
+ // Output:
+ // none.
+ // Return:
+ // ostream &os The stream pointer
+ //
+ s.ReadAscii(&is);
+ return is;
+}
+//
+//______________________________________________________________________
+Bool_t AliITSv11GeometrySPD::Make2DCrossSections(TPolyLine &a0,TPolyLine &a1,
+ TPolyLine &b0,TPolyLine &b1,TPolyMarker &p)const
+{
+ //
+ // Fill the objects with the points representing
+ // a0 the outer carbon fiber SPD sector shape Cross Section A
+ // a1 the inner carbon fiber SPD sector shape Cross Section A
+ // b0 the outer carbon fiber SPD sector shape Cross Section B
+ // b1 the inner carbon fiber SPD sector shape Cross Section B
+ //
+ // Inputs:
+ // TPolyLine &a0 The outer carbon fiber SPD sector shape
+ // TPolyLine &a1 The Inner carbon fiber SPD sector shape
+ // TPolyLine &b0 The outer carbon fiber SPD sector shape
+ // TPolyLine &b1 The Inner carbon fiber SPD sector shape
+ // TPolyMarker &p The points where the ladders are to be placed
+ // Outputs:
+ // TPolyLine &a0 The shape filled with the points
+ // TPolyLine &a1 The shape filled with the points
+ // TPolyLine &b0 The shape filled with the points
+ // TPolyLine &b1 The shape filled with the points
+ // TPolyMarker &p The filled array of points
+ // Return:
+ // An error flag.
+ //
+ Int_t n0,n1,i;
+ Double_t x,y;
+ TGeoVolume *a0V,*a1V,*b0V,*b1V;
+ TGeoXtru *a0S,*a1S,*b0S,*b1S;
+ TGeoManager *mgr = gGeoManager;
+
+ a0V = mgr->GetVolume("ITS SPD Carbon fiber support Sector A0");
+ a0S = dynamic_cast<TGeoXtru*>(a0V->GetShape());
+ n0 = a0S->GetNvert();
+ a0.SetPolyLine(n0+1);
+ //for(i=0;i<fSPDsectorPoints0.GetSize();i++)
+ // printf("%d %d %d\n",i,fSPDsectorPoints0[i],fSPDsectorPoints1[i]);
+ for(i=0;i<n0;i++){
+ x = a0S->GetX(i);
+ y = a0S->GetY(i);
+ //printf("%d %g %g\n",i,x,y);
+ a0.SetPoint(i,x,y);
+ if(i==0) a0.SetPoint(n0,x,y);
+ } // end for i
+ a1V = mgr->GetVolume("ITSSPDCarbonFiberSupportSectorAirA1");
+ a1S = dynamic_cast<TGeoXtru*>(a1V->GetShape());
+ n1 = a1S->GetNvert();
+ a1.SetPolyLine(n1+1);
+ for(i=0;i<n1;i++){
+ x = a1S->GetX(i);
+ y = a1S->GetY(i);
+ a1.SetPoint(i,x,y);
+ if(i==0) a1.SetPoint(n1,x,y);
+ } // end for i
+ // Cross Section B
+ b0V = mgr->GetVolume("ITSSPDCarbonFiberSupportSectorEndB0");
+ b0S = dynamic_cast<TGeoXtru*>(b0V->GetShape());
+ n0 = b0S->GetNvert();
+ b0.SetPolyLine(n0+1);
+ for(i=0;i<n0;i++){
+ x = b0S->GetX(i);
+ y = b0S->GetY(i);
+ b0.SetPoint(i,x,y);
+ if(i==0) b0.SetPoint(n0,x,y);
+ } // end for i
+ b1V = mgr->GetVolume("ITSSPDCarbonFiberSupportSectorEndAirB1");
+ b1S = dynamic_cast<TGeoXtru*>(b1V->GetShape());
+ n1 = b1S->GetNvert();
+ b1.SetPolyLine(n1+1);
+ for(i=0;i<n1;i++){
+ x = b1S->GetX(i);
+ y = b1S->GetY(i);
+ b1.SetPoint(i,x,y);
+ if(i==0) b1.SetPoint(n1,x,y);
+ } // end for i
+ //
+ Double_t x0,y0,x1,y1;
+ p.SetPolyMarker(2*fSPDsectorX0.GetSize());
+ for(i=0;i<fSPDsectorX0.GetSize();i++){
+ GetSectorMountingPoints(i,x0,y0,x1,y1);
+ p.SetPoint(2*i,x0,y0);
+ p.SetPoint(2*i+1,x1,y1);
+ } // end for i
+ return kTRUE;
}
git://git.uio.no / u / mrichter / AliRoot.git / blobdiff